Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
D:\nRF51822\mergehex.exe --merge D:\nRF51822\s110_nrf51822_7.0.0_softdevice.hex _build\ble_app_hrs_s110_xxaa.hex --output hrs.hex
I am doing it.But one of the files to...
hi i am working on nRF51822 chip, trying to flash code using keil IDE through STLink debugger. which i have attached image . while flashing the code it is showing Flash is...
I have a peripheral that pairs to a central and establishes a connection (without bonding) without any trouble. When I disconnect the central (e.g. cutting power to the central...
Hello All,
For the S120 softdevice active scanner, it appears that when ADV_IND is received and a scan request/response exchange occurs there will be two BLE_GAP_EVT_ADV_REPORT...
Hi,
I am getting the NRF_ERROR_INVALID_STATE error when I call dm_security_setup_req in my security timer timeout handler. The function's description says I'll get this...
Hi,
I would like to store firmware version number at a particular offset from the application start address so that it can be retrieved by boot loader as explained here...
The comment in dfu_init_prevalidate says the following
// To support application versioning, this check should be updated.
// This template allows for any application...
Hi,
As far as I know the ADC pins can be used as digital inputs. Is it the same with NRF9E5? I could not find anything like pros/cons. Datasheet doesnot say anything about...
Hi,
i have been struggling with UICR Config in nrf52. The code:
NRF_NVMC->CONFIG = (NVMC_CONFIG_WEN_Ren << NVMC_CONFIG_WEN_Pos);
while (NRF_NVMC->READY == NVMC_READY_READY_Busy...
Dear nordic.
We are developing nRF51822 with S120 as central.
When advertising from Peripheral, RSSI value is changed it's position.
Measured RSSI range is -60 dBM...
Hi,
I am trying to get the sniffer to work on my new Win10 machine.
I am using the PCA10001 board.
I have tried:
SEGGER: 6.00g and 5.12f
Wireshark: 1.12.x,...
Hi to everybody,
I have configured the nrf52 DK (SDK 11) with FreeRTOS and the UARTE with a DMA buffer of 16 bytes and it works. The problem comes when I don’t want to...
Hi,
I'm working on ble_app_hrs_c application with Nordic beacon.
Using nRF51822 Ver.H0 with S120 and modified to using Internal 32.768KHz RCOSC and UART at 115200bps...
Hi guys,
I'm playing with a beacon kit, nRF51822-BK.
It works out of box, no problem but I have a simple question. One of our customer asked me if is possible to control...
Hello,
I am using nrf51 SDK version 10.0.0 along with the nRF51822, and I believe I have found an issue with a macro that is supposed to check the correctness of a bit...
