We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi there,
Using mbed i have currently programmed an nRF51 DK to transmit data through a custom service with 6 read only characteristics. Is there a simple way i can alter...
Hello.
I cannot get my head around app_timers. After reading the docs, examples and answers on the devzone I'm still unable to get it running. The timeout callback isn...
I am trying to add SPI to the ble_uart_example on my nRF51-DK but when I try to debug my code debugging just stops (All "step one line" etc. buttons grayed out) at this line...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi,
I'm using nRF51 Development Kit to program the beacons. I've connected the beacon just like it's described in the last update of this thread using the 10-pin adapter...
Hi,
I just noticed that the nrf51822 doesn't have an eeprom and I already had the pcbs done. Can I use the NVMC to write USER data on the CODE (is it flash memory are?...
I am trying to do over-the-air (OTA) device firmware update (DFU) on a device with bootloader same to the "dfu_dual_bank_ble_s110" example in the latest nRF51 SDK . On the...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
We are using Gazell to stream data at <=6mS intervals for very low latency wireless gaming peripherals. We'd like to have many of these peripherals devices (more than 24)...
Hello
I'm trying to get a SPI master onto my S210 programmed nRF51422. I'm using uVision 5 and have all the nordic packs installed and built off of the ant broadcast tx...
main.c
I am trying to talk to this sensor: www.meas-spec.com/.../MS5803-05BA.aspx via SPI... it quite seems to work as I get expected responses to commands but as the title...
Do the Nordic Boards offer some sort of config region where settings like the Bluetooth address are stored? I would like to change these settings without having to recompile...
I am trying to set up a GZLL star network on the 51822. I understand that a single GZLL host can support up to eight devices but whenever my host attempts to communicate with...
Hi Team,
Is there any example to understand Prepare Write Request/Prepare Write Response?
In ble_uart_app example, I am getting p_ble_evt->header.evt_id = 2 if I put...
