We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I need to set the SPI Mode NRF_DRV_SPI_MODE_0 for a 2nd chip (on the same SCK/MISO/MOSI) to NRF_DRV_SPI_MODE_1.The chipselect is handle by the application.
I can't do the...
Hello,
Is it possible to clone services of peripheral device connected with "Bluetooth Low Energy Standalone v4.0.0" PC application? I see it is possible in "nRF Connect...
nRF52840
NCS 1.9.1
I have successfully downloaded app_update.bin to flash and rebooted. MCUBOOT copies the new application correctly and it runs fine.
The boot process...
I opened an issue on GitHub, but the NRF Connect iOS repo has not been updated recently. Here is the link: https://github.com/NordicSemiconductor/IOS-nRF-Connect/issues/118...
Hi guys.
I'm using the development board NFR52840DK and I modified the sample in zephyr\samples\boards\nrf\nrfx to use twp buttons, sw0 and sw1.
The sw0 button reset a...
Hi,
I want to use my PC to send some message to dongle via USB, then the dongle send them to certain device via BLE.
If there is a sample that allows PC interacting with...
Hello,
I have tried running Blinky example with some Low Power directives in the code without success. I came here for help then.
The current consumption used by the example...
Hi All,
I am trying to port my current SES project (s140) from nrf52833 to nrf52832. My nrf52832 is spec'd at 512kb flash and 64kb RAM. Any help would be much appreciated...
Hi,
Trying to evaluate the nRF52840DK with Matter examples but none of them seem to compile.
Following error is the result
Building light_switch west build --build-dir...
Hi,
We are using nrf5340 nrf connect SDK V2.0.0 and we are unable to find the brownout detector configuration. For our use-case we want to trigger system reset if supply...
hello Nordic
i work with nrf52832, with ncs 1.7.1 (moving soon to 1.9.2)
i have some issues with my spim clk and i think (not sure) its related to working with spim0...
Hi
I am trying to bring up the Nordic LE Audio example (nrf/applications/nrf5340_audio) and a basic BLE peripheral (nrf/samples/bluetooth/peripheral_lbs) on the nRF5340...
I want to run a single-edned comparator using the 1.2Vref. I cannot find details on a few items. just how to set it up
A) what is the variance on the 1.2V reference voltage...
Here is a warning during build
C:/v2.1.0/nrf/subsys/bluetooth/mesh/shell/shell_utils.c: In function 'shell_model_strtosensorval': C:\v2.1.0\nrf\subsys\bluetooth\mesh\shell...
