But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
I want to use my PC to send some message to dongle via USB, then the dongle send them to certain device via BLE.
If there is a sample that allows PC interacting with...
Hello,
I have tried running Blinky example with some Low Power directives in the code without success. I came here for help then.
The current consumption used by the example...
Hi All,
I am trying to port my current SES project (s140) from nrf52833 to nrf52832. My nrf52832 is spec'd at 512kb flash and 64kb RAM. Any help would be much appreciated...
Hi,
Trying to evaluate the nRF52840DK with Matter examples but none of them seem to compile.
Following error is the result
Building light_switch west build --build-dir...
Hi,
We are using nrf5340 nrf connect SDK V2.0.0 and we are unable to find the brownout detector configuration. For our use-case we want to trigger system reset if supply...
hello Nordic
i work with nrf52832, with ncs 1.7.1 (moving soon to 1.9.2)
i have some issues with my spim clk and i think (not sure) its related to working with spim0...
Hi
I am trying to bring up the Nordic LE Audio example (nrf/applications/nrf5340_audio) and a basic BLE peripheral (nrf/samples/bluetooth/peripheral_lbs) on the nRF5340...
I want to run a single-edned comparator using the 1.2Vref. I cannot find details on a few items. just how to set it up
A) what is the variance on the 1.2V reference voltage...
Here is a warning during build
C:/v2.1.0/nrf/subsys/bluetooth/mesh/shell/shell_utils.c: In function 'shell_model_strtosensorval': C:\v2.1.0\nrf\subsys\bluetooth\mesh\shell...
Hi,
I downloaded Android-nRF-Toolbox and ble library source code from https://github.com/NordicSemiconductor/Android-nRF-Toolbox https://github.com/NordicSemiconductor/Android...
Hello,
My thingy:91 was working nicely, even connecting to nRFcloud. But after updating the firmware to thingy91_fw_2022-09-15_7a358cb7 and Update jitp certificates it doesn...
Currently we are developing a board that requires to functionality of the nRF52840 dongle (pca10059), however for convenience sake we have incorporated.
The problem arises...
Hi,
I use NCS 2.0.0 with 2 nrf52840, one peripheral with manny notification and one with Bletooth Shell sample.
I can see all notification of the peripheral with my Phone...
I need support on Long range in Bluetooth Mesh network. I am coding on VS-Code, toolchain nRF Connect SDK v2.0.0. Zephyz OS v3.0.99, nrf52833 SOC, 8dbm in Kconfig (TX power...
