This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
So i have my nRF5340 DK and have been pretty successful in getting my Mesh working with some Thingy:52 devices, some Adafruit Feather devices and some Sengled Lamps.
Groovy...
I am trying to read from the LIS3MDL sensor using spim on the nrf52840 dongle. I gave the rx buffer with the length of 7bytes. Whenever i tried to read from the sensor, I...
Speaking with various MVNOs, not all carriers support PSM or eDRX when roaming, so I am interested in the time and wattage consumed transitioning from PSM --> to ready to...
Hi,
I want to connect "nRF52840 Dongle" via SPI to an 6-Axis IMU (Adafruit ICM-20649 / InvenSense). The collected data (cycle = appx. 10ms) should be sent out with BLE to...
Hi.
A simply question: i want to get data on " LL_VERSION_IND" control PDU from peer. Example: my device is slave, after connecting to me i want to get LL_VERSION_IND data...
Hi,
When will you release the SDK for the PCA0054 (12 antenna array) with nrf52833DK?
Specifically, code that supports more than 1 tag detection
If full SDK is not available...
Hi,
I have worked on a lot of projects on nRF51/52 devices. But still i do not understand why exactly should we use custom/multiple services for each kind of data (like...
Hello,
Having now finished the BLE and I2C sensor my final stop is the SPI sensor before production. I can rebuild and successfully run the ncs playground example .
My...
Hi, I am working on SPI master-slave application, as in, on one BL653 I am running SPI master driver, I am able to observe the waveforms for clock and data transfer from master...
Hi,
Are BMD-341 and MDBT50Q–U1MV2 modules are exactly the same?
Why I asking this question is, I saw some differences between them in the datasheet especially in the...
Hi all,
I would like to program the nRF dongles and Thingy 52, but i don't know how to choose right development kit to program the dongle and thingy.
Which one is best...
Hi,
We are developing a wireless protocol based upon 802.15.4 for nRF52840 and have some trouble with the MAC layer. To begin with, a mlme reset is requested and then an...
SDK: NCS 1.8.0
Based on: Peripheral LBS example
Central: Mobile (iPhone)
Peripheral: nRF52832
Hi,
I am attempting to integrate NVS within my custom application based...
Hello,
I noticed that nrf_ble_lesc_request_handler() hangs when I have NRF_CRYPTO_BACKEND_CC310_ENABLED and use a NRF_SDH_BLE_TOTAL_LINK_COUNT bigger than 5. Using the Oberon...
Hi,
I have the following error when trying to compile either the light_switch or light_bulb matter projects on nRF Connect SDK v1.8.0:
opening dependency file C:/Users...
