Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello The function scan function is being implemented with nrf52833. The desired action is an action that does not connect immediately when the scan starts, but when you receive...
Using nRF52840 and SDK15.3
I'm seeing some documentation on the DFU process and all that but I'm having to write my own bootloader transport (and lower) layer to implement...
The current PC release of nrfutil.exe, v6.1.2, gives 9 malicious warnings on VirusTotal , including warnings from a couple of the big anti-malware vendors.
I would suggest...
Hi all
I used to use bmi160 for my application with nRF52833 and I am upgrading to bmi270 with nRF52840.
I am struggling to make work the functionalities I used to have...
Hi,
I have an application where I want to send sensor data using advertisement message, and read this message by an iPhone. For test purpose, I am currently transmitting...
Hello,
So, I have a working BLE project on the nRF52840 Dongle and I developed and debugged everything on the DevKit, using Zephyr/nRF Connect for VS Code. From there, I...
Hello, I'm using nrf52832, my own custom board, the UART pins are 10 out, 9 in, no stop bit, no parity and no hardware flow control, baud rate 115200.
Ever so often, in...
Hi,
I'm using SDK17.0.2 example(ble_uart) on nRF52832.When I enabled SPIM to drive sensor,and send data, RTT Viewer logging SOFTDEVICE: INVALID MEMORY ACCESS.
BTW I have...
Hi! This might be non-coherent, I apologize in advance as my knowledge in RF is very limited.
We're developing a sort of 'TX-negotiation protocol' between our peripherals...
I keep receiving the email stating the following, even after having all the points taken care of :-
1. I am using a active / approved DevZone Account.
2. I am using the...
Background - found during testing with proprietry application derived from the 'light_ctrl' sample in nRF Connect SDK, with Time & Schedule Servers added, on an nRF52833DK...
Hi,
i have a question regarding the USART NUS error handler.
In my setup, two Nordic BLE Chips are communicating via the USART service.
One chip is acting as a central...
hello everyone,
i am using nrf52810 with my custom board which contains mpu6050 accelerometer and Gyro-meter so now i want to achieve connectable beacon like it should be...
Hi, I received nRF9160DK kit with a SIM. I want to test SIM registration on Vodafon Network , Data transfer to a server ? Is there any concerned sample available in SDK Connect...
Hell Respected Members.
Referring to my previous question https://devzone.nordicsemi.com/f/nordic-q-a/85221/retaining-rtc-time-after-resetting-nrf52840 . give me a reply...
