But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
The poly1305 implementation is only covering the obsolete RFC 7539 which got updated by RFC 8439
https://github.com/nrfconnect/sdk-nrfxlib/blob/main/crypto/nrf_oberon/include...
nRF Connect SDK v1.7.1 sample \ncs\v1.7.1\nrf\samples\bluetooth\mesh\light_ctrl\
Long transition times fail due to a 16bit value which needs to be 32bit (I believe, can...
Question regarding nrf5340 ADC input tolerance
If I power the nrf5340 from the VDDH pin at 5V, will the ADC input pins be able to read up to 5V then or just 3.3V?
Thanks...
We have a product that uses the nrf52. Due to availability issues I need to port that project to the nrf51822. Since the nrf51 supports up to sdk 12.3.0 what is the best way...
Hello All,
Thank you in advance for your time and interest in this issue and willingness to provide suggestions.
We have a product that uses the nRF52832 processor in...
Hello,
I'm trying to connect a sensor to the nRF9160 board using the example Asset Tracker v2.
My sensor (SHT30) is connect in I2C to the pins 31 (SCL) and 30 (SDA). In...
Hello,
Does nrf9160 support C++? If it does, which version? I saw a similar question over 2 years ago in which C++ was not recommended ( https://devzone.nordicsemi.com/f...
SDK: v17
Softdevice: S112
I am currently checking the throughput using nrf52810 or nrf52805.
In device A, data is input as Uart and checked as device B input data...
Hello everyone! I want to evaluate the exact power consumption from the camera (Arducam Mini 2MP OV2640) using the nRF52840-DK as well as its SDK with the nrf52-ble-image...
Hi,
I am trying to implement USB DFU on a NRF52833 with nRF5 SDK for Thread and Zigbee v4.1.0 and nRF5 SDK v16.0.0.
In a first step I want to perform this on the devkit...
Hello,
I have several issues with the new nRF Connect for VS Code SDK, I put them into one ticket, although, some of the issues could be related directly to nRF Connect...
Hi
1: According to this ticket: https://devzone.nordicsemi.com/f/nordic-q-a/28335/nrf52840-usb-pins-impedance you recommend to not
have any serial resistors on the D...
Hello!
I have installed Android nRF Mesh application version 3.0.3.
Also I bought Yeelight YLDP10YL lamp which is qualified mesh product ( https://www.bluetooth.com/learn...
