But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi,I recently started using a PPK2 board and at first had no trouble setting it up with the Power Profiler Software from the nRF Connect for Windows.
What I realised is...
Hi,
nRF9160 in nRF9160DK with NCS v1.6.0 and master, power consumption measured by PPK2.
With CONFIG_SLM_EXTERNAL_XTAL=n nRF9160 average power consumption is ~7uA after...
My use case is that the nrf9160 is running as a serial lte modem and I have a host controller that is controlling the ENABLE pin. VDD will always be powered so can I leave...
Hi All,
I am using a 3rd Party (Japan) nRF51822 module in a device and it is running a modified Direct test mode firmware without Soft device. Upon testing, it is found...
Hi everyone!
I'm trying to make the NFC work on a custom board. I'm using a BL653 series (nordic nRF52833) and nRF Connect SDK v1.6.0. I am running the record_text example...
I found a similar thread for this issue, but there was no solution... So I want to ask here again here
I follow the video "Introduction to the Zephyr RTOS"
https://www...
We are using a IDE Segger Embedded Studio (SES) for our development with nRF52832.
We need to use IDE which supports IEC 62304 standard.
Our Query as follows:
1. Is...
Sometimes when I call sd_ble_gatts_hvx, it can take several ms to return. Most of the time it takes very little time (<1ms), but occassionally it takes up to 34ms, my connection...
Hi Nordic Team,
In my application, I'm trying to read 512 bytes of data continuously from the STM32 master device. nrf52840 acts as a slave device. Every time I receive...
I have a DK of nRF52840, which is from 2016, and want to use it to test the LE Coded broadcast.
But it seems that 2016 DK does not support it, so I want to replace the chip...
Hi
I am working on direction finding examples, based on CTE feature that is introduced in BLE v5..
I have build and run both "tx" and "rx" examples successfully as described...
I have developed two PCBs that each use the rRF52840 chipset in the form of the BL654 modules from Laird which include PCB antennas.
I based the software project on the...
Hello,
I am trying to transmit weight measurements via BLE from a nRF52840-DK to a proprietary app. I am able to successfully transmit the data to the nRF Connect app on...
