But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
dear all:
I use the latest sdk17 to test the ANCs sample on the 52840 DK。 The address of the example is: SDK_Path\examples\ble_peripheral\ble_app_ancs_c。after...
I have a example application (gatt central) that works fine on the nRF52DK dev board. I'm able to change the advertisement name, connect to it with my phone, and see the characteristic...
Hello everyone,
Yesterday I found a strange behavior with the NRF9160 GPS on NCS v1.5.1:
When configuring the GPS to run in Single Fix mode, running on MFW v1.2.3, I noticed...
*** edit: Problem solved. My project file had build config set to "release", I had to change it over to "Debug".
Kindly close the case ***
I have an i2c program running...
Hello,
I would like to ask for guidance, as I am at the very start of a human interface device (HID) controller development, considering BLE nRF52840.
The use case I would...
Hello!
I am trying to get basic communication between two nRF24L01+ modules to work on Teensy 4.0's, but I am having trouble transmitting and receiving.
Here is the wiring...
Hello, DK:nrf52810
sdk:17.0.2
In my project i have to advertise accelerometer and gyro value through beacon so i have done with using https://devzone.nordicsemi.com/f...
Hi Nordic Mesh experts,
I'm testing for the BLE mesh using light_switch example based on nrf5 sdk for mesh and nRF Mesh APP.
From the printed info on the APP during connection...
So I now have nRF 52840 dk and I'm working through the secure bootloader example. I am using SES. (Windows).
So I built and flashed the the app and it looks fine, it has...
Using gdb watchpoints I was able to see that running spm_request_random_number() (which is executed in sys_rand32_get) changes content of first byte of backend_cb_log_backend_custom...
Hello DevZone,
I am working with a project whereby we use both the nRF52832 and the nRF52840 and what blew my mind is that Segger has absolutely no problem in downloading...
Hello Nordic, we are trying to develop a system using nRF52833 and want to reuse the xtal 32.768k and xtal 32M clocks for other purposes. For that, we need to know at the...
Hi,
Using SDK14.0.0, soft device: s132_nrf52_5.0.0
If Segger embedded used them use latest sdk as below, because sdk 14.0.0 has no support for segger embedded.
nRF5_SDK_17...
Dear Nordic,
We've faced with the issue on Zephyr Shell NUS module.
The captured reaction is just on 'Enter' press in terminal. It seems it has some kind of...
