We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
What are different options to load the soft device on custom board? Currently, I am using nRFGoStudio to load the softdevice on nRF52840 DK. We will not have segger hardware...
My app uses a proprietary service and characteristic UUIDs; the app needs to completely manage all characteristic reads and writes. With nRF Connect, I can see my service...
Hi Community,
For community's help I success to create 12.3.0 DFU version get work.
So now I try to make all hex(softdevice, bootloader, application) to one hex file...
Dear Nordic,
We are trying to figure out the difference between the working/feature set of nRF_crypto file and mbedtls.
Which one is better and why?
Ambimat
Hello,
I wanted to ask which uart library we have to use in SDK16 and which configuration to have a LOW POWER UART
We are in development phase on the devkit PCA10040 and...
Hi guys,
So i have some Nordic DK board including some dongles, NRF52840 DK, NRF52833 DK running with Zigbee and thread SKD 4.1.0 and make a mesh out of them. But I have...
Hi,
I have to control 16 pin output pins based on the 16 pin interrupt.
Is it possible to have 16 pins interrupt in nrf52840 . Pin change interrupt
when i config
...
I use SDK 15.3, nrf52840.
https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development-kit/posts/setting-up-the-timeslot-api
Normal use most of the...
We are developing a new product that requires extremely low power consumption with a target to run advertising intervals of between 2 to 10 seconds.
We are using the nRF52805...
Hello everybody, My nRF9160 simply does not connect, I already followed all the instructions that come in the quick guide, I successfully registered the SIM card in the nRF...
I am using nrf52832_xxaa with SDK v16.0. I have a requirement to write into UICR register use seggger but I don't see any sample for that. Is it possible? If yes, please provide...
Shalom!
I am getting with the nRF9160, BSD TCP sockets, a connect() errno=116 after disconnecting and closing a previous TCP connection.
I have two TCP servers with the...
Hi eveyone!!
Im new to BLE, I have tested the ATT_MTU example and it has worked perfectly but I'd like to implement it for one client and two servers. I've already made...
Hi everyone,
We are designing boards using the nrf52832 microcontroller and using the nrf52dk as a design reference. In the BOM for the nef52dk board we noted HS crystal...
