But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
root@homelinux:~# ./nrfconnect361x8664.AppImage --no-sandbox
its will show the main menu but can not open the sub APP, like programmer, lte monitor they can not opened
I am using the nRF GFX library to print some text on an LCD. The font, prepared with The Dot Factory v.0.1.4, is stored in flash per the examples in the sdk.
The problem...
I am manually installing the nRF Connect SDK using these instructions https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_installing.html and in paragraph 4...
Although I have a fair amount of experience with PIC microcontrollers, I am new to the nRF52 and I am finding it difficult to make the transition. However I have been given...
HI
I use nRF5_SDK_17.0.2_d674dde ble_app_hids_keyboard。 I want to composite KB and Media player。
but only KB can work。
I find many people have this question。 but do...
hi
I use nRF5_SDK_17.0.2_d674dde. delete bonds have some problem.
1. when poweron before into main loop， use delete bond is ok。 can run to PM_EVT_PEERS_DELETE_SUCCEEDED...
Hi, I have the same issue with https://devzone.nordicsemi.com/f/nordic-q-a/59096/nrf52832-module-can-t-connect-j-link-anymore-after-flashing-zephyr-program-onto-it but the...
Hi, I got nRF5340 DK board and trying to run sample projects such as peripheral_lbs, peripherad_gatt_dm, etc. using SEGGER Embedded studio but BLE advertisement doesn't work...
Custom board, ncs v1.4.0, modem FW v1.2.3, SES v5.34a. The code is based on the Asset Tracker (v1), LTE with PSM, motion-activated GPS, using MQTT to send messages to private...
In the ble app uart example, I need the BLE device to be able to send out a null character. I noticed when I receive a message with a null character at the end from the UART...
Hello. I am receiving an input of 1 Hz. ADC is receiving 12 bits. uart's baud rate is 1000000. ADC input is output as UART raw data.
To do this, I modified the following...
hi,
I've found the sample for direction findings in the sdk-nrf github master branch (sdk-nrf/samples/bluetooth/direction_finding_connectionless_tx)
Will this code work...
Hello,
I want to extend the at_client sample with vanilla Mbed TLS (delivered with the SDK) supporting TLS. Later on, I want to be able to modify the Mbed TLS vanilla implementation...
In the past I was able to get the Serial LTE Example application working over UART0 on the pins used in my custom board. I did so by adding a file called nrf9160dk_nrf9160...
