I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I have an existing product using the nRF52832 SoC rev 1. We must transition to rev2 since rev1 is no longer sold. We use SDK12.0.0, with S132 V3.0.0. Have these software components...
Hello Team,
I have downloaded the Zephyr project and working on the LwM2M sample client application to make nRF52840 DK as an LwM2M client. I have followed the below link...
Hi,
Referring to White Paper nRF9160 Hardware Design Guidelines v1.0, what is the scenario (supply voltage, band, antenna VSWR, TX duty cycle...) behind maximum heat power...
Dear Sir,
I'm using nordic's example codes above to tx and rx, but i can not get them working properly. the LEDs should light on the receiver side according to the example...
I have a strange issue on the nRF9160-DK board using the nRF Connect SDK, GNU ARM for GCC v10.2.1, built using makefiles.
I have two threads that both wait on a semaphore...
Hi,
I am trying to change the tx power of Zigbee using the following APIs :
1) zb_set_tx_power(0x32); 2) nrf_radio_txpower_set(NRF_RADIO_TXPOWER_NEG12DBM); 3) nrf_802154_tx_power_set...
I am currently using a nRF52-DK to follow the connection between two external devices. I run the sniffer and start/stop the sniffing via Wireshark. When I start sniffing,...
Dear Team, I face Following error with example downloaded from Github,
error 1) Output/Release/Obj/saadc_pca10040/ses_startup_nrf_common.o: in function `InitializeUserMemorySections...
Chip: NRF52840
Firmware platform: Wirepas V5
Hello!
I am now writing firmware for a product based on HW&SW mentioned above.
It is powered by battery and sends data...
Dear Sir,
please do me a favor to reply on my following question.
our project is a keyboard which we expect can work on both ble and 2.4G. we will use other brand of of...
Hello
I am using nrf52832 and sdk v17.0 I recently succeeded in controlling several ws2812 LEDs through I2S. And now I'm going to combine these codes with the others.
...
Hello,
I'm trying to get the SPI drivers working in slave mode. I have tested my master (Atmel L21) on an Arduino and I can see my message clearly. I'm trying to get nRF52833...
Hello
I want to access to the buffer to see what I am transmitting for then change the data to transmit to be able to verify, also I want to know where I can find de Kconfig...
