After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
We feed the nRF54LM20A’s VBUS pin (the USB high-speed PHY) from the nPM1300’s VBUSOUT, so that the PMIC’s input protection guards the module and the processor sees VBUS only...
With PM device runtime enabled ( CONFIG_PM_DEVICE_RUNTIME =y ), calling uart_irq_tx_disable (actual driver function uarte_nrfx_irq_tx_disable) may result in increase the PM...
So far, 10,000 chips have been produced. More than 100 chips encountered the situation where there was no pwm output at pin P0.20. The program is the same. A multimeter was...
I'm working on an open source smart watch project https://github.com/Protocentral/healthypi-move-fw . I'm after serial communication with another device, so I need to re-enable...
Hello,
I am experiencing an issue with my nRF52 DK. The target nRF52832 appears to be working, but the on-board debugger is not functioning.
Symptoms:
No power/debug...
The "Programmer v4.8.0" from "nRF Connect for Desktop v5.4.0" does not appear to use the Windows system time correctly, and this problem has appeared for us with the new UTC...
Dear Nordic, We are testing NTN NB-IoT on an nRF9151 DK against an Amarisoft callbox. We'd like to see how the modem finds the cell and estimates Doppler and timing before...
Hello,
after having a product using a nrf52832 MCU for a while in production using nrf connect sdk 2.5.1, we now wanted to supply a first firmware update. However, while...
Looking the nRF7002 reference schematics in the datasheet and I'm wondering if you really have to use so many different capacitor values for decoupling. I would like to harmonize...
During reset and initialization are the NFC pins configured as GPIO or as NFC?
If they are in NFC mode can you clarify if they have any special behavior on boot (pulls,...
We are currently evaluating the nrf9151 via the thingy91X
for our application we need the device to function in areas with no cell coverage and not drain the battery....
We will like to use the Nordic nRF9151 to verify our CP-EDT feature. For that we need an AT command to trigger MO ping but we have not been able to find such command in your...
Hello,
I have not found any information about the VBUS current consumption. Is this information available? Do you know how much current flows through the VBUS pin?
Thank...
Hi Nordic team,
I am using the nRF52840 HCI USB project as the controller firmware, with a Linux device acting as the Bluetooth host.
My application has multiple BLE connections...
Hi, Our nRF52840 (NCS v3.4.1, SoftDevice Controller) is a central that connects to smartphones running our app (phone advertises, nRF52840 initiates). About 12% of connections...
