At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello.
I found in Provisioing chapter on this document: https://www.bluetooth.com/specifications/mesh-specifications/
something like list of provisioning commands: ...
Hello.
I plan to perform antenna matching to improve the performance of my design.
I would like to know any differences when performing the match on bare pcb and pcb...
Hi,
I'm working on a test for the pulse width measurement, the input is analog signal.
I'm using a while loop, and use nrfx_comp_sample in the loop to get the voltage...
Hi All,
I just start to use the Thingy 52 and I would like to know if there is any source code for development purpose for Windows. Also, which development software does...
in SDK/examples/peripheral/blinky/ hex
there is one file
blinky_pca10056 _mbr .hex
in
SDK/examples/peripheral/blinky/pca10056/ mbr /ses/Output/Release/Exe
there...
Hi
I am very new to BLE...
We are looking into a new industrial product design that will be battery powered, and be capable of communicating with BLE sensors (Mesh not...
Hi!
My software setup consists of SDK 15.0.0 and SD 6.0.0.
I am using nRF52DK for flashing and debugging my custom PCB board on nRF52832.
I am developing an application...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
1) At factory first we will load Secure Serial Bootloader and SoftDevice...
We are building a prototype for a wireless solution using nRF52840 and we found that the UART included in this MCU does not support Odd parity. This is a major handicap that...
Hello, I am writing a Program where I use GPS and NBIoT. Recently, I wanted to combine the default GPS example code with an NBIoT Code, that connects to a TCP Server and when...
Hi,
We are using Eclipse editor for nRF52833 SDK 16.0. While searching GDB support for nordic devices i found following link
https://devzone.nordicsemi.com/nordic/nordic...
Hello,
I am using the nrf9160 and I am developing using zephyr. I have an nrf connect project in Segger IDE.
Generally I am able to edit and build my project. The problem...
dear :
i used sdk 12.3 development bt mouse. now i have a question.
when one mouse link pc , its mouse x/y axis is ok.
but if two mouse( same code) link pc. oen mouse...
Hi all,
I used nrf cloud gateway servie last week. It's work very well.
But today i get some problems
1. i can't delete device. If i delete device, then it will go to...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
I am new to DTM. I have related queries.
1) In nAN34 note, what...
