This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
hello
I have ble_app_hrs_freertos project for that, I have to make sleep and wake up the services in the project.
my question is that
1) how to sleep the service in...
Hi, I use nRF52840 dk PCA10056 and keil μvision5 . In Pack Installer of keil μvision5 , PCA10056 is not displayed . So I choose nRF52 PCA10040 , is it OK ?
I'm trying to send data from an IMU at about 50Hz over BLE to a smartphone. I'm finding that after some number of successful transmissions, I start to get the NRF_ERROR_RESOURCES...
Hi
I'm using the unmodified fatfs example in SDK16 with PCA10040 dev board connected to a Mikroe SD-Click board which is nothing more than a breakout board for microSD cards...
It is possible to provision the NetKey, AppKey and unicast address of a node using the serial protocol, using the following messages:
Mesh Subnet Add, Opcode: 0x92 - NetKey...
Dear Sir or Madam,
It´s the second time, I got the same error while start developing with nrf52833 demo board. For first step, I flashed a blinky example to the board -...
Now I'm trying to change a device name in `nrf_dfu_ble.c`. I set NRF_DFU_BLE_ADV_NAME like following.
And I imported `stdio.h`, `string.h`. And I edited `gap_params_init...
Hi,
im trying to flash a 3rd party demo board (MDBT50Q-512K Module Demo Board) with nrf connect for desktop. As programmer I use original Segger j-link edu mini.
As...
Dear Nordic:
My peripheral is configured to use MTU 247.
When connected by NrfConnect of IOS, I can receive NRF_BLE_GATT_EVT_ATT_MTU_UPDATED event and check the effecitve...
We are designing in the 52840 as a processor in a new sensor product and are looking at using the HOLYIOT YJ-18010-nRF52840 part that you indicate on your site is a third...
Env setup:
nrf52840 on PCA10056, SDK 16.0.0, S140, FreeRTOS, secure bootloader
Description:
I'm trying BLE background DFU in the application.
Had reference iot/background...
Hi
Is there any implementatiaon of nrfutil, and more specifically the DFU via serial port, as a C library? My use-case is I need to update an nRF52840 from within an already...
Hi,
I am able to set up uart async receive, but when I try to set the call back using uart_callback_set() so that i can call the uart_tx() routine to push the data out,...
Hello,
I am working on nRF9160DK. I am using SES for ARM (Nordic edition).
How can I import new libraries for any project? Let's say I want to import SD card libraries...
