Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hi
I did test two sample code with nrf52DK kit in segger embedded studio. with sdk ,nRF5_SDK_15.3.0_59ac345
1) ble_app_uart (I connect one sensor with UART,I did some...
Hi,
we are progress of designing custom board using nRF9160.
By reading nRF documentation, my understanding is GPS circuit in Dev kit is unstable/nonperforming.
Could...
I'm compiling a custom application using the CMake scripts in the nRF mesh SDK. The first time I flash to the nRF52832 a SIGTRAP occurs on sd_softdevice_enable. I cannot continue...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96 ,PC is windows 10
When I run the demo of b le_app_hrs on my development board,I use nrf connect app to...
SDK 13, softdevice 132
function fds_register results FDS_SUCCESS
by calling the function fds_init debugger stops, see comment in function below, and i see "unknown...
Hi
I'm a total beginner here and I have the gyroscope sensor LSM6DS3 and I have the nRF52 DK
I want to read the sensor's data via I2C (i.e. using SDA and SCL pins) using...
Hello.
This is becoming a very serious issue for me. When I program the nrf52840 dongle and when I switches on the power, it automatically goes into bootloader mode, means...
I purchased a sparkfun breakout board ( https://learn.sparkfun.com/tutorials/nrf52832-breakout-board-hookup-guide and schematic https://cdn.sparkfun.com/assets/learn_tutorials...
I'm compiling a custom application using the CMake scripts in the nRF mesh SDK. When I debug the application, even though the debugger is working – I can pause execution ...
I am trying to modify the central / peripheral relay example to not use the HRM and RSCS services and to use my own custom service instead.
I am following this tutorial...
Hi
I have the nRF52 Development kit and I can program it using SEGGER Embedded Studio IDE without problems. However, when I try to program it using nrfjprog, the Dk doesn...
Hi to all, I'm developing a new device that should be a multiprotocol: Zigbee (as coordinator) and BLE peripheral (with his own GATT) There is an example for this integration...
I asked a question on here couple of days ago, but I resolved that issue and have stumbled into a more concise and in the right direction. I am using ble_app_uart as my code...
I am using ble_app_uart as my code base. I included FDS.c and FDS.h when I compiled, it presented many config errors. I compared the two config files for the FDS example and...
Hi,
I have some problem about Keil hex output file.
At the end of hex file, there have some line as following image.
In (a) of above image, why "hex file" need to...
