Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hello there,
Prior to updating to the latest modem firmware i was able to successfully get responses from the DK.
Running the Asset tracker app as well as AT Client. ...
Hi
I am currently trying to connect the sht31 temperature / humidity sensor. First, I made an implementation based on the twi_sensor example. I did it all, the temperature...
Dear all,
I am quite new to embedded programming and I am looking for a tutorial/example code in order to communicate/configure an accelerometer sensor (LIS2DH12) with NRF52...
Hi,
I am running SDK 15.3, nRF52840 on a custom board, Softdevice 6.1.1 and SES.
When running the secure dfu example I find that the two segments uicr_mbr_params_page...
Hi,
NRF52932, s132.
I am currently migring from SDK 14.0.0 to SDK 15.3.0, I just finished to migrate from SDK 13.2.0 to SDK 14.0.0. The project with my app compile but...
Hi
I want to transfer a text filebetween nrf51 to nrf52 .Is this possible in nrf device. If it is How can i proceed ?. I am using NRF 15.0 SDK.
Please help me on this...
Hi
We are using today nRF52832 and communicate through Nordic UART service (NUS).
Sometimes we would like to transfer files from our device to the app. This is going very...
Hi All,
I have an application running on the nRF52832. From within the application I can store data to 0x2000 2010 - 0x2000 2028 and read the data back after a reboot/power...
Hi,
I need to generate a PWM signal with exact 2.048 MHz. I've just realized that
allows only decimal frequency. Even if I take 16 MHz and toggle it every 7,8,9 still...
Hi,
I have the NRF52 dev kit with NRF522832 chip. I am using SDK version 15.2 and the Segger IDE. I am trying to do OTA programming and have used this tutorial:
https...
I followed the nRF User Guide v2.2 for my nRF dongle and all was Ok up to "Install firmware with SEGGER J-Link point 6 e (loadfile Path\...\sniffer_pca10031.hex)". Got error...
Hi!
I am trying to get this example to work on my nRF9160 board: https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/spi/
It compiles and...
Hi,
if got the following setup:
Nordic nRF52840 DK (peripheral), custom iOS App (central), nRF Connect Desktop Version + another nRf52840 DK as sniffer.
My Goal: Changing...
Hello,
I need to interface both, an SD card and a smaller (~4Mb) external flash to the nRF52840.
The SD card will be interfaced using SPI.
For the external flash...
I would like to store some parameters in nordic's non volatile memory and be able to restore them after power off.I am using the soft device s130.
I have checked both examples...
