But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi All
Just bought a nRF52840-DK board (PCA10056) with the purpose to develop a project where nRF52840 is used as virtual com port.
The Lite edition doesn't allow to...
The HOME key is controlled by the HH protocol of IPHONE. After the Bluetooth connection, the original soft keyboard on the mobile phone cannot be played out. It is necessary...
Hi,
I'm using the nrf_queue library on SDK 15.2 and I noticed that it isn't possible to peek more than one element at a time.
It would be nice to be able to tell the library...
I'm using nrf52840 s140
I am trying to minimize a power consuming when there is no need to advertise but stay system on. Would nrf_sdh_suspend() be helpful?
if not, what...
Hello,
I am trying to upload the BLE DFU Secure bootloader onto my nRF52 DK for OTA programming, but I keep getting the build error "#error "D ebug public key not valid...
Hi,
I am simply trying to send a sample of data from a TWI sensor to smartphone via BLE with a 2 second delay between each send.
I've adapted the ble_app_uart and twi_sensor...
github.com/.../ble_app_uart_adc_simple
I have flashed the above program in the link on to my nrf51822 DK. I can see the values of the samples but i do not understand what...
Hi
I used your example to try out the ADC.
If I have 10 or 12 bit ADC selected and I am collecting 4 samples as per the example and I select 8x oversampling I assume this...
Hi there
I have nrf52 DK - PCA10040 which I believe contains nRF52832 IC
I have designed a new PCB that contains BT832 (nRF52832) module from Fanstel
My board is powered...
Hi all,
We are trying to use buttonless dfu for actual products.
We already finished testing dfu using \nRF5_SDK_15.2.0_9412b96\examples\dfu\secure_bootloader\pca10056_ble...
I have been setting up nRF9160 DK following nRF Connect SDK.
OS: Windows 10, 32 bit
I have trouble when I load asset_tracker.
I guess ninja would be related to this...
Hi,
I'm working on a structure based on a Raspi 3B+ with nRF52840 willing to connect to an IoT hub and working as a thread border router with 2 other nRF52840 connected...
Hello,
I have been trying to push down the current consumption by nRF24LE1 module that I am working with. I enabled register retention mode with the following code:
https...
Hello,
If a rf52 device running ESB in RX mode has multiple devices TXing on different pipes, is it possible to prepare a different TX response to be sent to each device...
As the title suggest, I am running into an issue where my nrf51822 bluetooth keyboard is drawing around 8mA, which I think is way too much.
I am using gazell protocol to...
