Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hello ,
I'm using ble_app_eddystone example and I would like to stop the advertising and TLM when I press button 2. I able to create a correctly inicialization of button...
we validate the example /ble_centeral/ble_app_multilink_central with NRF_SDH_BLE_TOTAL_LINK_COUNT equals 8. Change the number from 8 up to 15, it still work.
but when the...
in a ble_nus_c_evt_handler().
SDK13, nRF52, S132.
I made connect success. When it done, I send command to peripherial to start discovery. When event came
case BLE_NUS_C_EVT_DISCOVERY_COMPLETE...
Hi, when trying to read a register from a chip using the IIC interface,blocking mode:
uint32_t ms5837_cmd_read(uint8_t *data, uint8_t length, uint8_t register_address)...
On a custom board with an nRF52832, I have some LEDs I'm driving from the pins 9 and 10. One or both of these pins are used for the NFC antenna unless you configure them as...
I am trying to understand the whitelist feature by following the HID Key board peripheral example on S140 v5.0.0.-2_aplha on nRF52840 dev kit. I am using iPhone SE with nRF...
Hi all,
I'm trying to return a write response in nRF sdk but so far no success.
Actually I'm still scratching my head to figure out how characteristic write works exactly...
I am trying to build and debug the Mesh v1.0.0 light-switch server example and getting a
cryptic error when launching the debug.
My environment is Segger v3.30 on macOS...
Hello,
I just bought a nRF52832 development kit
infocenter.nordicsemi.com/.../nRF52_DK_User_Guide_v1.2.pdf
The board can pair and data transfter with mobile after i...
With a little research, I came to the probably erroneous conclusion that the "NRF_ERROR_INTERNAL" error I keep getting is likely caused by my not using a twi event handler...
hi
i did the setup according to border router setup guide on Nordic info center. all run fine but when i tried to run command ""panid 0xabcd" it saying not found
Good evening.
I write a project on nrf51822 in which there are a number of services with a set of characteristics (write and read). I need to limit access to some characteristics...
Good day!
I'm working on NRF52 and its default timeout for advertising is 180s. But I am unable to stop the advertising event even after that. I tried to change the timeout...
Hello,
is there a certain amount of time the nRF52832 has to stay in RXIDLE between the reception of two packets when receiving several of them without disabling and re-enabling...
