At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hi,
I am driving 8 RGB LEDs directly from 51822, meaning there are 24 individual LEDs sinking current into the chip. The LED are off or partially on most of the time, but...
I have programmed the system_off with 2 causes of wake-up on 2 different pins.
When the device is woken up, how can I check which pin is the wake cause ?
Thanks for...
Hi,
I use SDK 12 softdevice 130 2.0.1
The example project of HID is running on my nrf51822 board, it is pairs with iPhone but the windows 7 write that the HID driver...
Dear,
I am now testing Power Profile Kit. Using nRF52 DK.
But Strange, Measured Value is strange as attached picture.
Is there any problem on my measurement or setup...
Hi there!
I am trying to develop some application using ANT, and for that I bought some nRF51 (10031) dongles and one nRF51 DK (10028). In the beginning, I tried to use...
We are trying to dump SDK 12.1 examples and advertise the example, we used Segger embedded studio to dump the code, bps example. we followed devzone.nordicsemi.com/.../ to...
Hi,
I'm using an nRF52832 with the S132v2 and SDK 11 and wanted to test the ble throughput.
The nRF52832 should send as many as it can to an "normal" BLE-USB-Stick.
...
In SDK 11 the FreeRTOS port has the following line is declared in portmacro_cmsis.h
#define portNRF_RTC_PRESCALER ( (uint32_t) (ROUNDED_DIV(configSYSTICK_CLOCK_HZ, configTICK_RATE_HZ...
After updating from sdk11 to sdk12, the application only starts in debug. If started with reset, it hangs. I am running on a pca10028 board an with EmBlitz 1.0. NRF51 is QFACA1...
When I test the example, When I disconnect my phone of the nordic board.
I can use the other Phone to connect the nordic board
So, I think that how to avoid the connect...
I compile blinky_pca10040
I use IAR EWARM - ARM Cortex compiler
I have a Rigado BMD-300 on my PCB
Use J-LINK EDU
When I try to download and debug, I get the error
"Failed...
Hi
I came across this article:
www.nordicsemi.com/.../Bluetooth-Smart-hearing-aid-receives-stereo-audio-direct-from-iOS-devices-and-can-recognize-and-optimize-settings...
