But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello All,
I have been trying to get the Xiao BLE Sense with the nrf52840 chip in conjunction with the expansion board to access the SD card using the FatFS example from...
I don't want to use nrfjprog as the runner. I want to use jlink runner when flashing. However it doesn't work, neither do nrfutil.
nRF Connect for VSCode doesn't work when...
Hello,
OS: Ubuntu 22.04
SDK version: NCS 2.6.1
Modem firmware version: nrf91x1_v2.0.1
We are evaluating NRF9151 in a new design. We have some prototypes built...
For a project we need to evaluate DECT NR+. We have used the `hello_dect` example ( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/dect/dect_phy/hello_dect...
Hello, I'm developing an app that will allow a programmer to flash application firmware and modem firmware. I am able to flash application firmware via JLink Commander. The...
Hi, I had a project which was configured with upto 5 simultaneous connections. Recently moved from NCS 2.4.1 to 2.6.1 and now the advertising stops after one connection. I...
Hi,
I want to DFU the nRF52 from nRF91 over UART. And I find this sample: https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/cellular/lwm2m_client/fota_external_mcu...
We are working with Zephyr to program the development kit for now and later the real board,
We need access to both UART0 and UART1 but we can't seem to get UART1 to work...
Attempts to build the Matter light bulb same fail for me under these conditions:
A new nRF Connect SDK install on Ubuntu
Toolchain v2.7.0
SDK v2.6.1
VS Code...
Hi,
For Production I need to program by SWD 10 nRF52832 devices simultaneously. The production tools will be prepared for separately connecting 10 SWD interfaces to 10 different...
Hi.
I am experimenting with an internal temperature sensor (TEMP) on an nRF52810 microcontroller and have some questions:
1. How to select a crystal oscillator as a source...
We are developing nRF52840 battery powered device, NCS 2.5.2.
Wanted to use shell for external commands for system testing (currents must be low when the debugger is not...
Hey,
I'm currently working on a legacy project that uses the NRF5 SDK. Rewriting the project to use the nRF Connect SDK would be tedious, time consuming and likely to introduce...
Hello support team,
I have question on how should i setup child image. In my project i need to use hci_rpmsg sample as child image for the bluetooth. However, the current...
Build environment is the nRF SDK Connect for VS Code extension with ncs 2.3.0.
I am trying to accomplish DFU over UART with mcumgr serial console in which primary slot will...
