This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I am developing a custom board using the nRF9151 module controlled by an external host microcontroller. The nRF91x1 is running the Serial LTE Modem (SLM) application.
In...
Hi,
I'm using nRF5340 + nRF7002 for project that use wifi but I have issue while reading the default MAC before recording a new one.
The products are tested inside a...
When debugging the exercise 1 application from `Lesson 2 – Reading buttons and controlling LEDs` of `nRF Connect SDK Fundamentals`, I cannot set a breakpoint wherever I want...
Working in a Windows 64 environment with nRF Connect SDK v1.5.0. Target is a custom nRF5340 board connected through a nRF5340-PDK as a debugger, via USB.
I can no longer...
Hello
nPM Power UP v 2.24 detects nPM2100 EK, but does not detect the CR2032 battery. The active battery model selected is CR2032 and the fuel gauge is enabled.
I placed...
Hello,
We currently use an nRF51822 device in our product with the top marking QFABC0 .
We understand that NRF51822-QFAB is the ordering part number, and that QFABC0 is...
I'm working on a project for the nRF54L15. Until now I have not been using mcuboot, but since I added SB_CONFIG_BOOTLOADER_MCUBOOT=y to my sysbuild.conf, I get an error when...
in the datasheet table 80 "GPIO port mapping" the function "CAN-RX" is only listed on P9.4 and P2.8 are these the only two pins it can be assigned to ?
I am struggling to...
Hi Dev,
Development platform: NRF54L15 + NCS 3.0.2. We use k_uptime_get() to obtain the system uptime and perform task scheduling. Everything runs normally when the device...
I need to create a firmware to the nRF9151 SMA DK that can send a message to me (it can be via MQTT, but I prefer the nRF Cloud) containing info about the location of the...
Hi,
I'm trying to debug a Zigbee issue and for that I want to try some Zigbee samples on the nRF52840DK. But all links for Zigbee in docs.nordicsemi seem to be broken. All...
I'm running into a bit of an annoying situation every time i run ' west flash --build-dir ./build' in the command line. It rebuilds always after a successful build i set when...
To anyone trying to create the reflector for this combination there is an important conf file to add to the project. You should add android_ranging.conf to your build that...
In NCS v3.3.0 the signing of binaries fails when building the Non-Secure application (build with TF-M) in combination with XIP, split images and disabled partition manager...
