We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I'm using the nrf5340_audio application and with SDK 2.6.0. The Bluetooth address printed out in the terminal does not match what actually shows in advertisements. For example...
Hello, I am using NCS 2.9.0, an nRF5340, custom board files (see attached), and no external flash and I would like to use simultaneous DFU over BLE. I believe this should...
Hello,
I work on a board with nRF9160 and nRF52840. I can perform firmware update of both application and mcuboot for nRF52840 (using serial recovery mode) from the nRF9160...
Hi, I'm having problems with migrating my project to SDK v2.9.0. I'm using mcuboot and I want to use b0n on the net core and update support for the net core application via...
Hello everyone,
This might be a somewhat silly question. I'm trying to use SDK v17.1, and have an issue with the app_timer library.
I remember that before SDK v13 one...
Hello,
In BLE service whether can I use same Characteristics UUID ( Ex : using 0x2A6E / Temperature or 0x2A1C / Temperature measurement) with only difference in the description...
We're using nrf52833 and our target board is already running our program well.
Then
we'd like to flash by using Jlink SWD programmer.
So, we connected vref, gnd, swdio...
We have found a nrf52833 DK (PCA101000) with id, 685888541 with 2024.4.
So, it might be used as previous project in our company.
Anyway, I tried to test with this DK board...
based on SDK v2.9.0
1 Central, 4 Peripherals, Repeat the following:
Power off 3 Peripherals, wait a while, power on 3 Peripherals.
The following error usually occurs...
Hi
I have a nRF52832 Device, and develop by nRF5 SDK 17.1
Now, I have a project base on BLE_Central \ ble_app_uart_c , and also need to use Dfu OTA function
so I refer...
Is there a way to modify the distance measurement sample code to where it is intended for one transmitter and multiple receivers versus between just two devices? I am trying...
Dear,
I’m using nRF Connect SDK 2.7.0 with BLE Mesh and wondering how to adjust the TX power dynamically. When setting the TX power using a predefined option like CONFIG_BT_CTLR_TX_PWR_PLUS_8...
Hello.
I am trying to run an alarm clock using the RTC calendar. In the main loop I see the time being printed, but there is no response from the alarm callback, which I...
Hi,
in my case I need to flash the nRF5340DK board with only a standalone merged_domains.hex , which I get from another co-worker, no source code. how to do it?
Best...
Hello,
I am experiencing an issue while trying to connect an external flash memory (MX25R64) via the QSPI interface on an nRF52840-based custom board. My pin configuration...