We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I'm using the nrf5340_audio application and with SDK 2.6.0. The Bluetooth address printed out in the terminal does not match what actually shows in advertisements. For example...
Hello,
I work on a board with nRF9160 and nRF52840. I can perform firmware update of both application and mcuboot for nRF52840 (using serial recovery mode) from the nRF9160...
Hi, I'm having problems with migrating my project to SDK v2.9.0. I'm using mcuboot and I want to use b0n on the net core and update support for the net core application via...
Hello everyone,
This might be a somewhat silly question. I'm trying to use SDK v17.1, and have an issue with the app_timer library.
I remember that before SDK v13 one...
Hello,
In BLE service whether can I use same Characteristics UUID ( Ex : using 0x2A6E / Temperature or 0x2A1C / Temperature measurement) with only difference in the description...
We're using nrf52833 and our target board is already running our program well.
Then
we'd like to flash by using Jlink SWD programmer.
So, we connected vref, gnd, swdio...
We have found a nrf52833 DK (PCA101000) with id, 685888541 with 2024.4.
So, it might be used as previous project in our company.
Anyway, I tried to test with this DK board...
based on SDK v2.9.0
1 Central, 4 Peripherals, Repeat the following:
Power off 3 Peripherals, wait a while, power on 3 Peripherals.
The following error usually occurs...
Hi
I have a nRF52832 Device, and develop by nRF5 SDK 17.1
Now, I have a project base on BLE_Central \ ble_app_uart_c , and also need to use Dfu OTA function
so I refer...
Is there a way to modify the distance measurement sample code to where it is intended for one transmitter and multiple receivers versus between just two devices? I am trying...
Dear,
I’m using nRF Connect SDK 2.7.0 with BLE Mesh and wondering how to adjust the TX power dynamically. When setting the TX power using a predefined option like CONFIG_BT_CTLR_TX_PWR_PLUS_8...
Hello.
I am trying to run an alarm clock using the RTC calendar. In the main loop I see the time being printed, but there is no response from the alarm callback, which I...
Hi,
in my case I need to flash the nRF5340DK board with only a standalone merged_domains.hex , which I get from another co-worker, no source code. how to do it?
Best...
Hi.
I wanna evaluate nRF52840-DK. However, when I tried to install Toolchain on Visual Studio Code, a message "Failed to fetch available toolchains." is displayed. "nRF...
Hello,
I've been using nRF54L15-DK devboard (0.9.2 revision on the label) for about a month now without any problems until today.
I wanted to change VDD output voltage...