Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
when i got a nRF5340 DK,
firstly,i use the vscode to open sdk and build ,
secondly,start to run the ncs2.1.2 sample (path:v2.1.2\nrf\samples\bluetooth\peripheral_uart...
I wan't enable approtect by add this line in main.c:
const uint32_t approtect_set __attribute__((used,at(0x10001208))) = 0xFFFFFF00;
but when i compiled at IAR,its show...
Hi, I'm setting up my environment on a new laptop. The project I'm working on requires tflite-micro and before I found that I needed to add tflite-micro to the 'name-allow...
Hai Team,
I am working on NRF52840 based on the BLE Connection handle
Here I am using the ble_app_multilink_central example of SDK
case BLE_GAP_EVT_ADV_REPORT: { uint32_t...
Hello,
I'm following this tutorial to learn how to create a Matter application from template. I did all steps and wanted to build the application. However, the build failed...
Hello,
I'm using the nrf52-quadcopter example from NordicPlayground. After successfully building the project and connecting the MPU6050 , I got a hang during sensor initialization...
Hello,
I had bought 3 sets of Audio DK and had managed to brought up in BIS and CIS mode using the default sample project, however the output is mono output. Can I checked...
I've started to get this error when trying to do a DFU update on nRF Toolbox (v5.0.8): "Can not create Firmware".
The same firmware file worked before on the same device...
Hi. I'm using nrf5340. I confirm internal clock(LFRC RC osc) exist,I want to remove external 32.768kHz X-tal. If yes, how can I turn on LFCLK RC oscillator in my source code...
Hi,
I was successfully able to flash the peripheral_uart code to the dongle and then connect to the Nordic APP.
But it does not connect with the UART when in BLE mode...
I am working on nrf52810. I raised the RAM size in the linker file, which is larger than the real physical RAM capacity, for the testing purposes. I anticipate a hard fault...
Hi:
I use mqtt_ Sample routine: MQTT is connected to the server, and I shut down the server. At this time, the 9160 status has not been updated, but is still connected....
Hi
1、Now we connect the VDD to the battery voltage (3.4-4.2), and the VDD_GPIO is fixed at 3.3V. In order to match the GPIO of other peripheral cpus, will all GPIO be connected...
We plan to use the 52840 to make a module with an external flash, if we apply the QSPI peripheral, must we use the P0.23,P1.00,P0.21,P0.25,P0.19 pins recommended in the specification...
I want to run my software on nRF52832. It is already running on nRF52840.
What are the changes I would require making this transition.
We are using soft devices and all...
