After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I am working on developing an application for nRF52833 DK (PCA10100) using nRF5 SDK_v17.1 and nRF_802.15.4 Radio driver v1.6. I am using the s122 Soft device on the device...
Hi all,
So I was following this guide for updating my firmware over BLE: https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu#dfu_over_bluetooth...
Mesh SDK 5.0, SoftDevice S140 v7.2.0, NRF52840, SEGGER ------------------------------------------------------------------------------------ Hello, My problem is that I can...
When i open the Toolchain on my mac it loads and put upp a crash page. i have already: restarted my mac, reintstalled and restarted but i get the same crash
The System...
Hi, I currently have a project with an nRF52832 chip using SDK 14.2, I would like to upgrade the project and change the chip to nRF5340. Is there a way to migrate the project...
Are there any examples showing use of the MQTT library using Bluetooth as the Link Layer? I see this on Zephyr's repo zephyr/subsys/net/l2/bluetooth at main · zephyrproject...
Here is a warning I get linking an application that uses nRF DM library 5/14] Linking C static library app\libapp.a [6/14] Linking C executable zephyr\zephyr_pre0.elf c:/toolchains...
Hi,
Can any one list what are the reasons for sd_ble_gap_connect returns NRF_ERROR_DATA_SIZE?
In ble_gap.h NRF_ERROR_DATA_SIZE error code doesn't exist for sd_ble_gap_connect...
Hello,
We have already product with BLE 4 and now we are moving to BLE5. As per the example code we have updated our code to BLE 5 but we are not seeing advertisement...
Purpose: to develop a central device using nRF5340 and to enable both BLE Mesh and AoA features.
Questions:
1. nRF5 SDK supports nRF51 and nRF52 series but not for nRF5340...
Hello,
We were middle way during the development when we found out that we had a higher packet loss than what is acceptable.
So we start to analyze this issue.
Scenario...
Hi,
I reviewed the PCA10121 schematic for using SPI4 pins to connect to Semtech SX1262. Since SPI4 bus also connected to SD card and DSP. I checked to see if SPI0..3 pins...
In my application, we regularly transmit a stream of notifications from a Peripheral Server to a Central Client. The general strategy for this is to enqueue a packet, and...
Hello in my app I based it on the BLE UART example and have it pretty much up and running but I need to be able to send multiple messages from the Central to the Peripheral...
