Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Specifically, the example is examples/ble_central/ble_app_uart_c
I want to first verify my understanding of this example. In this example, should I be able to type in my...
Hello,
I am currently trying to flash a nRF51422 chip that will be placed on a custom PCB board using the pin20 on the nRF51 DK board. I had connected the chips pins as...
Hi,
I'm using TIMER1 CC0 for SAADC sample triggering through PPI and it's working well.
In order to check sampling frequency, for debug pourpose, I'm using PPI fork for...
I've been using the radio functionality directly, without the nrf sdk. Everything works great for 802.15.4 transmission and reception with one really odd exception: packets...
Can someone please post a simple example of using the internal oscillator with BLE? Modifying the ble_app_blinky example to use the RC would be ideal. No matter what I do...
Hi support team,
Now i am trying to understand the LPN machenism based on the LPN example. I cannot make sure where the bear handler is started.
There is a function bearer_handler_start...
Hello,
I'm planning to work on a device which should have two nRF5340 modules on a small PCB (they will be max 2cm apart from each other). Both modules will broadcast data...
Greetings,
I am using the NRF53 DK along with the Zephyr/Beacon (nRF Connect SDK v1.91) example for an ultra-low power application. I would like to know how I can change...
Hi,
I have nRF5340 DK and nRF52840 DK and Flashed Central_hr_coded in nRF52840, Peripheral_hr_coded in nRF5340 DK. Followed the steps of Testing as showed in below link...
I am following various tutorials on how to run an example DFU
I've tried: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v17.1.0%2Flib_bootloader_modules...
Hello,
I setup a BLE Peripheral that advertises a service with 2 notifications. Each notification has 240 bytes of payload data. When I connect with a client and subscribe...
Hello,
I followed the following guide for creating a modified Blinky example app that boots from the mcuboot. I attempted to flash both the merged.hex and zephyr.elf to...
I am using NRF52832 DK, SDK 17.1.0, S132 Softdevice, Segger 5.42a and rtt viewer v7.62.
I am using blinky code from example.After building and debug the code I disconnect...
I want to send the data packet from the BLE using GATT service and after that BLE mesh is initialize, using the Mesh opcode need to Disable the GATT service of the BLE. For...
