Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hello, im trying to implement the UARTE Driver for simultaneous Use of Bluetooth and asynchrounos Uart TX/RX on a nRF52840 and nrf9160. The Problem is that neither RX or TX...
Hi
i want use a nRF52840Dongle as a Zigbee end device, when power up, i get following message:
I: nRF5 802154 radio initialized ***** delaying boot 5000ms (per build configuration...
Hi, I have just started evaluating nRF52840 using the dongle and Development Kit. I have successfully tested the Openthread network using CLI project. Now I want to try out...
Hi experts, The situation is following, the NRF53 shall receive multiple packets. After the reception of one of the packets the next one shall be received at the same frequency...
Hello,
I am struggling to commission a light bulb matter sample device (nrf52840dk) with the CHIP tool running on my Linux laptop. I set up an OpenThread Border Router with...
I had configured zephyr.dts file for UART and I2C pheripherals. And when I tried to build an application it is giving below error
Board : nrf5340 Application name : SHT...
I implemented the nRF52840 (auto)upgrade with an nRF9160 on the nRF9160DK. I did my development with the Serial Modem LTE application from nRF Connect SDK 2.0.0. I noticed...
Hey All:
I'm trying to install V2.0.0 of the NRF Connect SDK on a fresh Ubuntu 22.04 VM, and the whole thing seems broken.
Here's my steps:
install the nRF command...
Hi, I have found several aged topics on Devzone but need this feature and would like current state. If it still not supported, is there any example implementation on how manage...
Is there a way to rebuild (clean and build) a project in Visual Studio Code with the nRF Connect Extension? A web search shows how to do it with the CMake Extension ( https...
I am using the Connect SDK v2.0.0 and attempting to use TCP in the stock CLI example to mimic the demo shown here . When I flash the v2.0.0 CLI sample on my nRF52840dk, "...
Hi everyone,
I have some devices that are communicated through RS485. nRF52840 DK supports RS485 communication?
Do you have suggestions of how should I connect those devices...
I have a custom board with 8 LED's and I use pwm API led_on(), led_off, led_blink() etc, to turn them on, set brightness and blink and everything works fine except one case...
I am using nRF52833 DK and I am running Light switch server in one DK and Client in another DK Advertising interval was way too high(around 9Second) so decided to change it...
Hi
According to Amazon documentation, it is possible to connect a smart home device to Alexa with the Bluetooth Low-Energy (BLE) mesh wireless communication technology....
