This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I have connected a nRF5340 DK board which the Programmer can connect to. I then drag the two .hex files for the Heart Rate Monitor demo over to the File Memory Layout window...
I've was able to use brand new PPK2 to make test measurements few days ago and it was working fine. I've connected the unit today and software have issue recognising the device...
After reading through the nRF21540 datasheet, I have a few questions.
1. Is section 5.5 saying that even though the spec for VDD is 1.7-3.6V, VDD needs to be between 3.45...
Hello everyone,
I'm now having a problem while using nrfx_spim_xfer on nrf52840. I want to use nrfx_spim_xfer with a callback when transmitting is done.
My setup code...
Hi,
For a development evaluation, I am looking to program nRF52833 to have it interface with "IS25LQ040B" serial flash chip through SPI-1. I found lack of examples and...
I am using the "nRF5_SDK_17.0.2_d674dde" for nRF52 development.
Would like to get the SoftDevice and nRF52 device for confirmation after OTA.
1. When using the sd_ble_version_get...
I am trying to send a OnOff output cluster information to Co-ordinator when a button is pressed in the nrf52840 DK. The problem is the during the initial registration, the...
Hi.
i want to power my nrf52840 with 2 AAA batteries i connected them directly to the module. Is there any Bluetooth signal strength difference when battery voltage drop...
Hello !
I have taken example /examples/crypto/nrf_crypto/aes/aes_ccm
and modify & g_nrf_crypto_aes_ccm_star_128_info instead of ccm
and initialization is failed
...
Hi everyone,
I'm looking for the max output current VDD can source (REG0) when the NRF52833 is configured as High Voltage Mode (see pic for context).
The NRF52840 has...
I need to send bulk data to an MQTT topic on a server hosted by AWS. I'm trying to use datamode option the serial_lte_modem sample but I'm running in to lots of problems....
Hi
I have five custom boards, same batch.
I used one of the boards for developing FW, based on the MQTT simple sample.
The FW uses CA certificates in an h file like...
Hello!
I am evaluating using nrf5340 for a very simple application (literally would only be a few lines of code). In it, I want to pass some information from the network...
Hi,
I am working with a nRF52832 in the nRF52-DK. I am trying to set high logic level of digital outputs to 1.8 V. I have been reading about different operation modes (normal...
