Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Speaking with various MVNOs, not all carriers support PSM or eDRX when roaming, so I am interested in the time and wattage consumed transitioning from PSM --> to ready to...
Hi,
I want to connect "nRF52840 Dongle" via SPI to an 6-Axis IMU (Adafruit ICM-20649 / InvenSense). The collected data (cycle = appx. 10ms) should be sent out with BLE to...
Hi.
A simply question: i want to get data on " LL_VERSION_IND" control PDU from peer. Example: my device is slave, after connecting to me i want to get LL_VERSION_IND data...
Hi,
When will you release the SDK for the PCA0054 (12 antenna array) with nrf52833DK?
Specifically, code that supports more than 1 tag detection
If full SDK is not available...
Hi,
I have worked on a lot of projects on nRF51/52 devices. But still i do not understand why exactly should we use custom/multiple services for each kind of data (like...
Hello,
Having now finished the BLE and I2C sensor my final stop is the SPI sensor before production. I can rebuild and successfully run the ncs playground example .
My...
Hi, I am working on SPI master-slave application, as in, on one BL653 I am running SPI master driver, I am able to observe the waveforms for clock and data transfer from master...
Hi,
Are BMD-341 and MDBT50Q–U1MV2 modules are exactly the same?
Why I asking this question is, I saw some differences between them in the datasheet especially in the...
Hi all,
I would like to program the nRF dongles and Thingy 52, but i don't know how to choose right development kit to program the dongle and thingy.
Which one is best...
Hi,
We are developing a wireless protocol based upon 802.15.4 for nRF52840 and have some trouble with the MAC layer. To begin with, a mlme reset is requested and then an...
SDK: NCS 1.8.0
Based on: Peripheral LBS example
Central: Mobile (iPhone)
Peripheral: nRF52832
Hi,
I am attempting to integrate NVS within my custom application based...
Hello,
I noticed that nrf_ble_lesc_request_handler() hangs when I have NRF_CRYPTO_BACKEND_CC310_ENABLED and use a NRF_SDH_BLE_TOTAL_LINK_COUNT bigger than 5. Using the Oberon...
Hi,
I have the following error when trying to compile either the light_switch or light_bulb matter projects on nRF Connect SDK v1.8.0:
opening dependency file C:/Users...
Hi i have a problem i put buttonless dfu on my chip and everything went ok i can do OTA updates and everything works perfecly but i have a problem when i connect via j-link...
