But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
On a nrf52840 running SDK 17.0.2 and Softdevice 7.2, while being connected to two devices in central and peripheral role, I observe that on the connection where the...
I'm trying to see if there is a simple way to scan for ANT packets on all supported frequencies (not ANT+, which I know is on a single channel, 2457MHz). Just for the presence...
Hello, I am currently using the logger backend to send information via UART from the nRF52811 to a PC. This works well, but only for one way communication. I would like to...
I have nRF52840 dongles that have something already programmed on it. They are encased in plastic and I have no access to the little reset button. How can I install my SoftDevice...
Hi, I'm having trouble implementing DFU buttonless.
I ran the tutorial step by step in the following link: https://www.u-blox.com/sites/default/files/Add-NordicSemiconductorDFU...
Hi Nordic,
From some cases in the devzone, I know for nRF52 series, the ESB doesn't support 250Kbps mode.
One of my customer employ nRF51822 in their product, so I want...
Hi,
It seems that we are experiencing exactly the same as what is described in this topic by @kienasv. That topic seems closed for replies, and the solution has never been...
Hello ,
What is the purpose of the second line of the code in errata 89 ?
I mean this line ;
*(volatile uint32_t *)0x40003FFC;
did you use this one like nop ?
...
I need to install a BTLE application on an nRF52840 dongle that is enclosed in a case and therefore I do not have access to the reset button.
I have looked at some of the...
Hi, I'm using nRF52805.
My BLE code could connect & communicate data perfectly for the first time. After the disconnection, I can still see the signal. However, when I try...
Hello, new-to-this platform dev here!
I am implementing BLE bonding on my nRF52840 DK, which uses the S140 Softdevice. The DK is a peripheral and I'm using version 17.1...
Hi,
I need some help to choose an RF module for a new project.
I need:
* To connect to nRF24L with custom radio communications
* to connect to legacy standard bluetooth...
I use the nRF5_SDK_15.2.0_9412b96 , the sample is use a QSPI FLASH(MX25R64), and we want to change this QSPI FLASH. we will use GD25Q64E, which code should be modify?
I have developed a project with 9160, which requires real-time display of NB network signal on the screen. In order to save power consumption, I have set the Mode to PSM Mode...
Hello,
For us our IO rail is 1.8V. In this case do you see a big difference in power consumption whether REG1 is in LDO mode or DCDC mode? From 1.8V to 1.3V if in LDO mode...
