Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
I have seen examples of enabling CCCD by default in the forum but I have not seen anyone say it is not allowed according to the BT SIG.
https://devzone.nordicsemi.com/f...
Hi, I use NRF52833 and SW: NCS version 1.4.1 and its zephyr version is 2.4.0.
I would like to know if there is method to record program counter, stack pointer information...
Hi,
I have used "es_battery_voltage_saadc" in SDK 14.2 to read the voltage of battery, now I'm using SDK 17.02, but there is no es_battery_voltage_saadc.
Is there a better...
Hi
For the revision 3 of the nRF52832, I've updated to the nRF5 SDK V17.1.0 to apply the workaround for erratum 249.
Afterwards, I saw that there is a newer version of...
I have a BLE peripheral device using i2c, gpio. When the peripheral is not connected I want the lowest power consumption possible.
when i try to turn off gpio:
//sleep...
Hi Nordic.
I am using:
1. Mesh sdk V5.00
2. BLE sdk V17
3. NRF52840
I am trying to build a node with many elements and models. The software is based on the LC server...
A question regarding to nRFSDK 1.7: why does nRFSDK disable using BL2 inside TF-M? If our device needs BL2 with TF-M, how can we enable it? I can't enable CONFIG_TFM_BL2 if...
Hi Everyone,
I was wondering if it is something I do wrong, or if there is an issue with my module.
I have never managed to successfully upgrade the firmware of my nRF9160...
Hi,
is it any possibilities to multilink central with s112 in nrf52810 chip?
using sdk: sdk14
actually, i am using sdk14 with one central and one peripheral is fine...
Hello, All,
When using UART on nRF Connect SDK to communicate between nrf9160DK and nRF2833DK, I found that the data length of a packet sent by the UART on both sides is...
Hi,
I have started a new project that will use I2C and SPI devices. As a starter I took the example at /examples/peripheral/gfx/pca10040 since I am using a ST7735 based...
Hello sir,
I am using nrf52832 as Dev kit board with using Button 1 for long press event for an interval of 5 sec .I have defined the BT0_LONG_PUSH as BSP_EVENT_KEY_0 which...
Hi,
I'm trying to build the Zephyr NVS sample in SDK 1.6.0 and SDK 1.7.0 for nrf9160dk_nrf9160ns (Non-Secure) and build operation is failing with errors.
../src/main...
NCS V1.7.0
VSC IDE
In VSC you can create a custom board.
when i do this for the nRF5340 and build, it does not include the network core.
it also does not appear...
Hello
in order to reach low power mode I use the following :
bsd_shutdown(); // 3.4 ma.
nrf_regulators_system_off(NRF_REGULATORS_NS);
how can I recover from...
