We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I'm porting a bluetooth app developed on a PCA10040 to a prototype PCB with a Fanstel BT840F.
My development environment is
Windows 10
nRF Connect V3.7.1
Toolchain...
Hi I have create a firmware to exchange sensor data through UART / RS485 (MODBUS Slave).
I succeeded to create my firmware and test it with a USD Serial to RS485 device...
Running lwM2M_client routine into PSM with nRF9160 is about 450uA current， RTT is used for logging and all UART is disable.
I use ncs1.6.0.
What's causing 450ua?
How...
dear simon
First of all, thank you very much for your help，Now in my program, I also encountered such a problem，I use NRF_ qspi_ Nor the power consumption of my whole system...
Hi
I configure two IO output PWM, one of which outputs PWM all the time, and the other turns on PWM by timer intermittently ，The period of the former becomes wider，As shown...
I’m not able to connect my Thingy91 to the network. I have successfully registered my Ibasis SIM card in the nRF Cloud (or at least that is what I think I have done):
...
Hi,
I am trying to configure a basic output pin in the device tree configuration. I read somewhere a 'compatible' parameter is requires because it describes what will be...
hi team,
Intial we followed this link for system on --> https://embeddedcentric.com/lesson-14-nrf5x-power-management-tutorial/
Now we are trying to enable the constant...
Hai
I have an NRF52840 Development board with 1MB of flash. I have an requirement to store a large amount of data in a flash around 6k samples in one record.
For this...
Hello,
Im using E73-2G4M08S1C module based on nrf52840. Somehow even when in erased state its consuming a lot of energy and starts heating very fast.
Im trying to figure...
Hi Nordic team
I failed to demostarte multicell location sample.
Hardware: Thingy91
SDK: v1.6.0/multicell location
Modem: v1.3.0
Q1. At prj.conf, nrf cloud location...
Hi Nordic
We are developing our IOT product and we are starting our development of firmware on nRF9160 DK so that we can port that code to our custom PCB that will contain...
Hi,
My application is currently using s132 v5.1.0. The Release notes for s132 v6.0.0 say:
"Fixed an issue where incorrect timing calculations during the LE Data Length...
Hello
I am running this version of SES
SEGGER Embedded Studio for ARM
Release 5.34a Build 2021011401.44914
Nordic Edition
Windows x64
When I run my program in...
Hello,
I am using the pine watch hardware, to do some tests,
I configured through the overlay file, the I2C_1 to use pins 0.6, 0.7 as shown below,
&i2c1 { compatible...
