We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
In the nRF SDK 15.2, I am using the function idle_state_handle() which has a macro NRF_LOG_PROCESS() which is defined in another header file as NRF_LOG_INTERNAL_PROCESS()...
Hi all,
We've been trying to transfer data from 52840 custome board to android device via USB.
52840 device could be detected after connection but it cannot be accessed...
Hi,
I am looking for usb connect and disconnect events to be able to trigger some behaviors in our product.
I don't find any API for that, like subscribing via a callback...
Dear Members,
I tried to compile :
E:\nRF5_SDK_17.0.2_d674dde\examples\ant\ant_broadcast\tx\main.c
I got this error :
..\..\..\..\..\..\..\components\libraries\util...
Dear Members,
I want to port a code from :
E:\nRF5_SDK_17.0.2_d674dde\examples\ant\ant_async_transmitter\main.c
to be used with PCA10056 ?
Any ideas ? thanks
Hi,
I have following questions
1. How to define the limit for number of bonding information stored in internal ROM of nrf52832?
2. We want to verify the bonding functionality...
Hi Sir
We have a project with nRF5340,
Coz our product will be a smart watch, we will need to re-programming our product after full assemble in production line,
So,...
Hi all
We observed a strange behaviour with mcuboot / bootutil in our nrf9160 based project.
The bootloader log messages showed that something with the primary image is...
I run the ./nrf/samples/bluetooth/peripheral_uart example on 52840DK and connect to it using the nRF Toolbox UART section.
The connection works and I can send messages to...
Hello,
I want to modify the lte_ble_gateway app (nRF connect SDK 1.6.0) to connect with the nRF52DK advertising through the ble_app_uart (nRF 17.0.2) application. The lte_ble_gateway...
Hello,
I am trying to test 1 central 4 peripheral multilink(with saadc).
However, when the master-slave(central-peripheral) is connected,
the connection disconnected...
As the title states, my program (and a simple idle/hello world program for that matter) pull approximately 600-800 uA at idle. Same exact program, driver, and config on my...
Hi all, I am trying to write a driver for a TMP116 temp sensor based off the existing Zephyr TMP116 driver. I have added in functionality to enable the interrupt pin to enable...
