But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I want to use nvs in nrf cloud. A conflict is found between the nrf_cloud library and the nvs library. The nrf_cloud library will cause the nvs library to be unavailable,...
Hi, I have a product working with an android app with the nordic library for a nrf51822. I'm using auto connect but I would like just before performing a DFU to change this...
Hello,
I'm trying to run the MQTT simple sample, i don't know why but i can't build and run the project and also i cannot connect J-link.
Do you have any idea?
Thank...
Hi
If I log to RTT I can see ZCL packets decoded on the log using minimal logging but when i tried it with full logging (to get that on the zigbee_shell on the uart) I got...
Hello,
We have a custom design board using Raytac MDBT50Q-1MV2. We'd like to use the DC/DC regulator for REG0 stage for low power consumption. Please see the relevant part...
Hello,
In our product, we use the S132 v3 softdevice and legacy pairing with a static pin code. At startup, this pin code (that can be changed by the user) is read from...
in sample peripheral_uart in NCS1.5.0 ,I want to re-binding uart0 rx and tx pin . the default pin is p0.20 and p0.22 ,i want to rebind witn p1.0 and p1.1 .but i edit in prj...
Hello, I bought the Bluefruit LE Sniffer - Bluetooth Low Energy (BLE 4.0) - nRF51822 - V3.0 from Adafruit Bluefruit.
So, I downloaded nRF Sniffer for Bluetooth LE 3.0 and...
Hi,
I am trying to apply a whitelist during advertisement on my peripheral device. Only one central should be whitelisted at a time. The whitelist is empty on initial...
Hi,
I'm using nRF52840 with ble_app_uart of ble peripheral example. And I'm using IDE is SES.
I want to put two deep learning model into my project , the two deep learning...
Hello,
I have the NCS v1.5.0 and would like to use AES (in different modes) in my non-secure application.
Looking at the crypto libraries available described here http...
Hi,
I am using two nrf52840 boards and a Light-Switch example included in the mesh SDK. One board is programmed with the proxy client , and the other with the proxy server...
Hello I am in the process of developing a central BLE and I would like to be able to transmit 240 byte frames with a device. The problem I have during my tests is that I see...
Hi,
I get " Could not fetch memory size of target devkit: Error: Error occured when get library info. Errorcode: CouldNotOpenDevice (0x4) Lowlevel error: LOW_VOLTAGE (fffffff4...
