Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
How do I configure the chip to operate in radio mode or BLE mode on the same build?
It seems the radio mode example projects use no soft device, but the BLE project I want...
Hi guys,
I am developing the program for Mesh SDK where I will need to use different functionalities from different C files that I defined, into main.c. I have already defined...
so Im tring to use interactive command to output my personal content
same as the device command which out put the device message
but i want to find the function which...
Hi, Iam trying to integrate secure serial DFU over UART with ble_app_uart application. After integrating serial dfu code My application hardfaults at sd_softdevice_enable...
I'm trying the first steps of the initial tutorial with the nRF5340 kit, from here:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_gsg_ncs%2FUG%2Fgsg%2Ffirst_test...
ERROR: JLinkARM DLL reported an error. Try again. If error condition ERROR: persists, run the same command again with argument --log, contact Nordic ERROR: Semiconductor and...
Dear sir,
Need to print RSSI value , What should i use SCAN_START() OR ADVERTISING_START () , WHICH ONE SHOULD I USE ??? AND WHAT IS THE PROPER EXAMPLE ON NRFSDK
...
HI
I'm in the process of evaluating nRF5340 but am new to Nordic chips and development environment. Im running Windows 10 and I installed nRF Connect 3.6.1 and installed...
Dear All,
I would like to know information about QDID for nRF5 SDK for Mesh v4.2.0, we are developing costumed equipment using NRF52833 and we need to start the process...
Dear Nordic support team.
Our product nearly complete Rnd stage.
We face only one thing relate to "Cannot reconnect after unpair device with smart phone".
debug wit...
How can i give command from android device to ble board to get the percentage, temperature, or reset or shutdown the device with the help of receiving command from android...
I'm trying to register the SIM card of the 9160 DK at nRF Connect website,
but the website is always showing "still working..." for more than 15 minutes.
Do you have a...
Hello,
I am experimenting with setting up a network via grouping in the following manner.
Bulb_1 will be put into identification mode, and Switch_1 will detect Bulb_1...
Hello,
I am trying to send gps data using MQTT protocol. For this purpose I wanted to combine MQTT simple example with the GPS example. I added all the methods/dependencies...
