We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I been having an issue using the ZB_ZCL_REGISTER_DEVICE_CB to know when the ZC writes to an attribute that is of type 0x42 String type. It seems that the callback id changes...
Hello,
Whenever we reset our custom board with the USB cable plugged in and powered, the NRF_POWER->USBREGSTATUS has a value of 1. It will not go to a value of 3 ( OUTPUTRDY...
Hello
I meet a build problem, could any one help me solve this?
Mesh build enviorment: ubuntu + cmake
build command: cmake --build /home/yuguorong/work/nordicMesh/build...
Dear community,
I am using the nRF52840 dongle with the connectivity FW and set the max number of connections to 10 in the connectivity firmware (of course the RAM area...
Hello! I have a few questions and concerns.
1) There are two UARTs on nrf52833. UART0 and UART1. How do I get them to work properly? For UART1, work is available only through...
hi ，
thank for your browse，when i develop my keyborad,there is a problem in the use of usb.
this is my board hw:
and use pca10056 kd,and program the hex of road...
Hello, everyone!
I have arduino nano 33 ble board. I understand that this board contains nrf52840 and can be used in nrf sdk. I will connect the debugger pin and J-link...
Hello!
I am using an saadc examole to get sensor value using AIN3 and sending it on ble but now i want to make it interrupt base example can someone help me out how to do...
I am researching a way to send audio from a Microphone on an APP in iOS or Android and came across the Thingy:52. Is it possible to get some guidance on the App side to transmit...
I would like to use an analog microphone to generate a voice signal, measure it by an ADC, and then transmit the sound to the host. This is the cheapest solution, but I'm...
Hello,
I'm trying DFU from here . It works successfully with nRF52833 DK Board before Appendix 1.
The question is how to combine all which it is bootloader + sd +...
Hello all, I have question about ppi.
Like code shown above, I'm using ppi.
Here, MUX_INPUT_2 and MUX_INPUT_3 are name of pin.
I'm changing their state: from low to...
Hi,
We would like to know the default state of the NRF52840’s GPIO pins - is it high, low or open? The reason for this question – we need to know these pins’ behavior/state...
Hello Guys, I want to build some project with Nordic products but ı don't have any sample code , if you have sample code for Keil let me improve myself.Actually codes can...
