This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
We implemented FOTA updates based on the multi-service sample. In general, FOTA works well. When the FOTA starts on the nRF Cloud UI side the device receives NRF_CLOUD_EVT_FOTA_START...
Hello Nordic Support Team,
I am currently working with Distance Measurement (DM) and now need to implement the Nordic UART Service (NUS) on the nRF5340, using the application...
Hi Nordic team,
we are using the nPM1100 PMIC together with an nRF52840 and are encountering limitations due to the charging timeout.
Issue description
Charging stops...
I am trying to evaluate the NRF 52840 using the Gazell protocol.
I need some secured link between 2 devices with a low latency, and authentified (so no one can replace one...
Hello everyone,
I am experiencing excessive power consumption in a project based on the nRF9151 processor, developed using nRF Connect SDK 2.9.0.
My project uses two UART...
Hi,I am working with pdm mic to read data .I can able to get the audio data using dmic_read api in pcm format.I got clock of 1280000 and sampling rate of 16000 of each 16...
Hey! I have been using MQTT with QoS 0 to transmit my sensor readings to nRF Cloud. However, I see data loss regularly, and I expect that is happening between my device and...
Hi there,
In a custom developed board based off of MDBT53-1M, I am struggling with the serial communication using UART0 pins. Using the default settings, I have been successful...
I've tried running l2_e2_sol from Cellular IoT Fundamentals course on nRF9160DK with SDK 3.2.0 but I got:
My board is more than 2 years old and was unused for that time...
Hello DevZone,
One customer meets an issue. Needs an expert about Matter.
There are 5 Matter over Thread window covering devices which are already commissioned in 2 fabrics...
I am working on a project, in which we are using nRF Connect SDK v2.9.0 on a custom board with the nRF5340 SoC. The device is a BLE peripheral implementing a couple of GATT...
Hello,
I want to validate NB-IoT NTN connectivity using an nRF9151 SMA DK connected directly to an R&S CMW500 emulator.
Goal:
Connect to the CMW500 in NB-IoT NTN ...
I'm having an issue where my device doesn't wake from System OFF (on GPIO or VBUS toggle).
It worked on up to and including nRF Connect SDK v3.3.0-preview1. Doesn't work...
As the title suggests, I want to use west build without having to include the BOARD_ROOT parameter.
I have already referred to this link , but the results were not as expected...
