At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Dear Nordic Support,
I just got my Thingy:91 and I followed your Getting started guide. I registered the SIM card successfully but whenever I reached this step, it always...
According to the nrf52810 v2.1 data sheet, the radio draws 7.0 mA at +4 dBm TX power and 4.6 mA at 0 dBm TX power.
How much power is consumed at transmit levels from -4...
I live in Vietnam, I try to use NRF9160 dev board to connect LTE and NB-IOT but device cannot connect to the LTE/NBIOT network. I am using the at_client example with nRFconnect...
Hi
I am using fafs example from SDK 15.0.0
It was possible to write to the SD card by SPI communication. However, using SanDisk's 32GBSDHC, it became impossible to write...
Hello
I have both mai.c and app_sdcard.c "static const nrf_drv_spi_t spi = SPI_INSTANCE (spi_instance);" Want to use .
So using "extern"
main.c
app_sdcard...
I have already developed a beacon with nrf52840, but now I need to detect it with another nrf52840, but my problem is taht I need to use less power as possible, so I need...
Hi guys, after building and running a mesh network i've been wokring on, i ended up with an error
im wondering where i'd be able to find the mesh error table.. i can't...
I have custom board with BMP280 sensor & nrf 52832.I have interfaced BMP280 using twi interface. I am using SDK 15.2.0. and soft devices s132 V6.1.0 to transmit advertising...
We would like to achieve following:
Only peripheral devices should advertise data toward only central devices in the same application.
advertising data by peripheral...
Greetings! I'm trying to set up an nRF52 board as an SPI slave so that it would receive chunks of data irregularly from the master device (a Raspberry Pi in this case, if...
Hello,
I would like to know how to implement middle button click in hid mouse, by middle button click i am referring to scroll wheel click and the function associated with...
Hello!!
Is UICR.CLENR0 register disabled on nrf52SoftDevice?(only nRF51Chip??)
When writing with nRFgoStudio("Enable SoftDeviceProtection" CheckBox is on), the firmware...
Hello,
We are trying to build asset tracker based on a modification of board nrf/boards/arm/nrf9160_pca20035.
Every is good until we tried to enable secure bootloader...
Software : C / GCC - SDK 15.0.0 - SD140 6.0.0 - building on multiple platforms. Hardware : nRF52840-DK (Q1AAC0) - and secondary testing on custom board using the Fanstel BT840...
