We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hello everyone and Good day
I am a fresh graduate and its my first assignment at my job. I have to flash an LED at 1 Hz using NRF52810 BT 5 chip.
There are so many development...
Hi,
I am using nrf51422 interfacing with Ti's CC256MODA Bluetooth so here can you plz tell me how to do pairing with the TI's bluetooth .How to give passcode to the device...
Hi,
for my nrf52840 based project, I need to following peripherals :
2 X SPIM Master
2 TWIM Master
1X TWIS Slave
Given the resource sharing constraint, is this...
Hello guys
The nrf52832 uses 32 Mhz oscillator but I couldn't find much information about the oscillator in the chip document.
Can you give me a datesheet or something...
Hello,
when i try to flash code after loading s132 softdevice using nrfgo studio, i am getting erase failed,cortex-M4 error . but the fresh ble_peripheral alone is working...
Hi,
My goal is to send raw frames to some external device which is not nRF BLE example but commercial used device.
It is using some fixed service with fixed UUID and I...
I doubt Nordic developed a brand new GPS receiver for the 9160. Where does it come from (manufacturer and model)?
The Thingy91 Asset Tracker out of the box example has some...
The Thingy:52 Environment Service uses this structure to represent Temperature.:
This is wrong - it cannot correctly represent temperatures below zero but above -1 ...
pls advise if nrf9160 DK can work in RDP protocol , say the board is in US to work on NBIOT carrier or LTEM carrier . Can it be configured in some way to do evaluation remotely...
Hello!
It seems to me that GCC compiler optimization (-O3 -g3) somehow break the SAADC.
When enabling said optimizations the SAADC no longer gives me valid measurements...
Hello,
I'm developing a gateway and i would like to use advertising packet on sensor side to transmit data but it suggests that my gateway will be in permanent scan. I know...
Hi , I would want to establish a GATT Server application as well as integrate Bond Management Service from glucose example (ble_app_gls) in examples folder of SDK15.3.0_59ac345...
ble_db_discovery_start () returns NRF_ERROR_INVALID_PARAM (0x7)
This problem occurs when two peripherals are connected to one central unit. The two peripherals use the same...
Hey,
I am having trouble validating this idea through research. I was hoping someone could give me some ballpark feedback.
The setup:
- 15 NRF52832 devices on custom...
all set. while in linking stage i am getting
.\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol nrf_sdh_is_enabled (referred from nrf_fstorage_sd.o). .\_build\nrf52832_xxaa...
