We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi,
Please advise,
How many Peripherals can be connected to one Central? If my application need a connection of 50 Peripherals connected to one Central what I should do...
We bought a handful of nRF52840 Dongles and want to develop firmware based on the nRF Connect BLE app + nRF connectivity firmware reference design.
I am using v2.6.2 of...
Hi,
I need to read RSSI value without implementing the SoftDevice. Now I'm producing modulated and unmodulated carrier starting from the radio_test example. How can I read...
nrf52840 is ble central ,nrf52832 is ble peripheral,
nrf52832 is modify finish.
but i do not know how assign ble central .
now i use the example(ble_app_uart_c) to implete...
Hi,
I am using Timer0 to measure external pulse width. Using GPIOTE, PPI task and events. The problem here is, I am reading Timer0 Capture register as Zero always. Here...
Hi,
Now I'm using window10,nrf52840 and nrfSDKforMESHV3.1.0, and I want to achieve ota fonction within two nrf52840,I had read the Software Development Kit > Previous versions...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
How to select different Advertisement types ADV_IND/ ADV_DIRECT_IND/ ADV_SCAN_IND...
I have my nRF91 DK connected to nRFCloud, thanks for making that super easy! I'd like to review any debug data and learn more about the nRF91 which is new to mean but when...
Hello there,
We are a test lab based in Leatherhead UK, and would like to use your nRF52840-DK for setting up a test jig to communicate with a DUT(Device Under Test) ...
Hello,
I am trying to determine whether or not the SPI EasyDMA functionality of the nrf52840 supports double buffering in the sense that the DMA controller will switch buffers...
Hello, I have a problem with properly adding the Azure IoT SDK (C) into Segger IDE. Anyone already managed to get through that? My goal is to have Azure IoT Hub working with...
Hi, I'm attempting to use the nRF52832 Smart Remote 3 SDK for a project on an nRF52832. I wish to add Serial Output capability (for debugging purposes). I followed the example...
Hi,
I notice that inside the MESH SDK, "Friend" is actual a hex file from zephyr, which I cannot modify. My goal is to set a "Friend" to connect more than 1 LPN (low power...
Hello, community. I have a question about hardware and software setting for using 32Mhz.
(1) Software setting in sdk_config.h
#ifndef CLOCK_ENABLED #define CLOCK_ENABLED...
Hi, I'm searching a example project to do the qualifications test for my product. I'm using SDK 10, have you an example for this SDK? (in your site I found an example with...
