This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Dear Nordic Team,
I am using a nRF52832 module purchased from Adafruit ( https://www.adafruit.com/product/3406 ) and I would like to connect it with another device with...
Hi there
First I tell you what I'm, trying to do...
I want to made a connection between a robot and a pc. Over this connection I want to program the robot with new software...
Hi,
I'm using nRF52832 SDK 14.2.0 s132 dfu, softdevice 5.0.0.
And i'm trying to update SD + BL + APP to SDK 15.3.0, softdevice 6.1.1.
When i update pakage by nRF connect...
Hi,
I am trying to upload HEX files to a nrf52832 (on a Sparkfun Breakout board) with a nRF52 DK. The problem is nRF Connect Programmer don't recognize them.
I installed...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image. I am using ‘ble_app_blinky’.
In sdk_config.h, BLE_ADVERTISING_ENABLED is not...
Hi, I'm currently in trouble with the sd_flash_write function. I've already a library using this function running on the nRF52832 with the S132 softdevice. But when a tries...
I want to use TWI to read the sensor data. When using the software TWI, I found that the communication takes a long time, which will greatly increase the battery consumption...
Hey,
I'm trying to put the nRF9160 into System Off mode and am getting a bus fault error when writing to the REGULATORS module. This is the error output:
***** BUS...
Hello everyone,
I try to import a project from Keil to SES,
I 'v read the instructions in this article.
Segger Embedded Studio - A Cross Platform IDE
Generally I have...
HI:
I'm using a cli routine from the SDK，and I register the callback function zcl_device_cb() with ZB_ZCL_REGISTER_DEVICE_CB()，But whatever message I receive does not go...
Hello community,
I successfully flashed assets_tracker code into board and configure in NB-IoT using Configure NRF SDK project in segger studio.
I used Vodafone SIM card...
Hi, I use nrf52832's uart with a simple driver, not "nrf_drv_uart", because I don't know how to use receive and transmit interruption with "nrf_drv_uart". the uart drive i...
Is there a supported way of doing an unsecure flash (the nRF is hardwired via UART to a secure processor) without rebooting?
The HW design the nRF is integrated with uses...
I am using the nRF52840 DK to read data from an IMU sensor (STm LSM9DS1 9DOF). Like most sensors, you transmit the register number first (on MOSI), then continue clocking...
