But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
I'm trying to send data string from Central to Peripheral device using NUS.
If string length exceed 20 bytes then function return err_code = 12 (NRF_ERROR_DATA_SIZE).
...
I have some test code that uses VLOC_USER and when i write with authorization the data seems to get scrambled.
when i use
p_evt_write->data[0];
to get the data it is...
Hello,
I am new to Nordic devices. So it is tough for me to understand PWM examples. Can you provide me the simple code of PWM? Basically, I want to give a specific brightness...
I read somewhere that nrf52 has default tx power 0 dBm (I use S132 softdevice). I would like to set it to +4 dBm. How to do it? I know sd_ble_gap_tx_power_set function exists...
I am using arm-none-eabi toolchain for Linux and so far I had no problems with s110. However today I have written some simple application for s130 but it doesn't even start...
Hi,
I'm using two PCA10056 boards and my phone to perform the light switch mesh example. Now I want to perform something like, use nRF mesh app on my phone to turn on the...
hi i am working on ble_App_uart example in nrf52840 DK and i want to advertise in non_connectable mode. i have checked into ble_advertising_start() and ble_advertising_init...
i am working ble_app_uart example here in peripheral i changed the advertising mode from connectable to non_connectable mode and i checked in nrfConnect app the peripheral...
Is it just me, or does the CMSIS Configuration Wizard really not give any visual distinction between options which are 'Enabled', and those which are not?
eg
On the...
My first layout for the nRF9160 chip worked well but we were unable to locate the GPS amplifier.
We are working on finalizing our layout for a nRF9160 module.
We are still...
hello !
I am using nRF51 SDK 12 and even when I add the library of app_uart_fifo on keil it can't find app_fifo.h. As the screenshot shows, it is
please help for my...
hello ! i want to recieve data with nrf51 (multi_link_central) from another nrf51( ble_peripheral)
i dont have any error in my code but i have a part of my code how make...
Hi,
I am using NRF52832 as a BLE device and using the nrfConnect app to connect to it and access the custom characteristics and services. After connecting to the board using...
I am using two microcontrollers for my application, one of which is the nRF52. What I would like to do is transfer the firmware for the nRF and external uC as a single bundle...
Hello All,
I have 2 evaluation boards nrf53840 EVB "PCA10056".
I would like to run on them the "ble_app_uart" in "nRF5_SDK_15.3.0_59ac345" as following:
A custom board...
