We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Board：PCA10056 （0.9.3）
SDK：15.2
Softdevice：S140
Example：ble_app_blinky
Today，I follow this page Using an ampere-meter for current measurement to measure the current...
Used SDK: 15.2.0
Hello,
I want to print some debug messages over RTT after an error occured. After that I want to reset the system.
If I put the string into the que...
I've followed the steps to set up the SDK.
When I execute the batch file(setup_sdk.bat), there is something wrong occur (as below pic)
I've installed the git and add...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi there,
I am trying to use UART on the nRF52840 on a custom PCB. The custom board is connected to the nRF52840-DK with a debug connector. Am I free to set any pins on...
I want to create a router that only communicates with Bluetooth, not the gateway that connects to other networks.
The configuration is as follows.
C oordinator + Router...
Greetings,
I'm having troubles getting the Mesh lighting demo to work. Here are the details:
IDE = SES 4.12
SDK = nRF5 SDK v15.2.0, nRF5 Mesh SDK v3.1.0
SoftDevice...
Hi, Is there a usb hidapi sample code for nrf52840 somewhere? I know that there is a sample code of usbd_cdc_acm. Using the HIDAPI library link below , It will be beneficial...
Hi,
I am working on a Bluetooth Mesh project in which I am trying to add support for NFC, but I get the following error " error: multiple definition of `SWI2_EGU2_IRQHandler...
I'm new to nRF9160. I have some experience of implementing stm32 MCU and HL8548(3G module).
I want to send at commands to outside module like Wifi module, and receive return...
I have Nordic NRF 52840 DK development board, using Ubuntu 18.04, I loaded "ble_connectivity_s140_usb_hci_pca10056" to the board successfully. Then I powered cycle and cannot...
My setup: Eclipse, nrf52832 on a custom target board, s132, SDK13
I am trying to implement the workaround for the problem described here:
https://devzone.nordicsemi.com...
Hi everybody,
I would like to know how the module nRF9160 comes from the factory in it default configuration.
Is it possible to use it in UART mode only with the pin 86...
Hey guys,
I am currently using the nRF24L01+ (more specifically the module that has +pa +lna), and I am experiencing some odd behavior. I will briefly go over the devices...
