We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hello,
I am trying to program the application into the CortexM33.
I am using the lte_cloud_demo_v0.3.5 , compiled under Keil.
using nrfjprog:
\DemoPack1_EU-1.4\Firmware...
SDK version: nRF5_SDK_15.0.0_a53641a
Softdevice version: s132_nrf52_6.0.0_softdevice
PDK: PCA10040
I am using the PCA10040 as a peripheral. When a connection is established...
Of course accurate power consumption isn't possible to predict. However, it would be helpful to have a couple of basic numbers so we could do some back of envelope power calculations...
Hi everybody,
I am having a problem using pwm with ble_app_uart example, let me explain, I want to control a servo motor via Bluetooth, so I use the ble_app_uart example...
Hello, I've read here https://devzone.nordicsemi.com/f/nordic-q-a/24490/nrf52-dk-changing-reset-pin-from-p0-21-to-somewhere-else that reset pin cannot be reconfigured to any...
Hi Nordic,
I am using NRF52832/NRF52840 SDK 15.0 to design products. And I found a strange problem that the connection will be terminated by iOS device when connection...
Hi,
I'm developing a BLE device which has one custom service and three characteristic, each characteristic has read/notify properties. My proglem is, when my device connects...
Hi all,
I want to make a windows application that can switch the light of the CoAP server example. The CoAP windows code is not the problem.
Question is, how this can...
LIKE one of your collegue told me i tried to this...but it doesn't work on the dongle..
Dongle: SDK15.2.0\examples\ble_peripheral\ble_app_blinky\pca10059\s140\<your favorite...
Good afternoon,
I am trying to get cell-tower information from ZTE-M/NB-IOT cell-tower information, in particular RSSI.
In addition - a constant refresh-rate, ideally...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am trying to support old phones without BLE 4.2 data length extension.
I have read https://punchthrough.com/pt-blog-post/maximizing-ble-throughput-part-2-use-larger-att...
I am working on a project where I need to transfer the data from nRF52832 to ESP8266 through UART. I made the connections RX to TX and TX to RX.
I am using ble_app_uart_c...
Hello everyone,
I am having a problem with powering my nrf51822, I have 2 Li ion batteries to power my nrf51822 and a stepper motor, I put the batteries in series to have...
Hello,
Kindly asking for some guidance... We're working on a solution that requires us to distribute unique data sets (i.e., each nodes gets a different data block, approx...
