But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello Nordic ,
Do i need to implement the config_ client model so that the node can be named as a client and a provisionner in same time ???
however in the example of...
I am using SDK 15.2 with IAR's EWARM 8.30.1 and the nRF52840 Development Kit. My eventual target is the nRF52-Dongle. If it matters my development OS is Windows 7 64-bit....
I would like to write code to disconnect from any connected device. My system is a ble peripheral with s132 6.0.0.
My code calls:
result=sd_ble_gap_disconnect(BLE_CONN_HANDLE_ALL...
I starting working with examples for the nRF9160. Zyphr seems like a very complicated OS (like Linux with device trees, etc) and difficult to use with a debugger.
Is the...
Hi,
I trying to convert a stm32 function code to nRF52. The goal is to use a spi periperal on my custom board.
In this application we need to have 2 bytes transfert. That...
I can communicate with success from the pc to my custom nrf52832 device (SDK 15.2, S132v6.1) using the pc-ble-driver (sd_api_v3) with Tag 4.0.0 from Github. Great work!
...
Hi,
I designed a nRF52832_xxAA board, use an external power switch, without DFU features its operating normally.
When I add the DFU function according to the Sample code...
Hi,
I am using nRF51822QFAA-R7 controller(DC DC setup) in my design.
I am generating +3.3V from rechargeable battery and providing +3.3V as a supply to drive these controller...
Hi,
I'm just getting started with nRF mesh (sdk V3.00) and I've built the light switch sample successfully and deployed it on three nRF52832 development boards but provision...
hello,nordic
I use NRF52840 QSPI+FatFs+USB-msc(..\nRF5_SDK_15.2.0_9412b96\nRF5_SDK_15.2.0_9412b96\examples\peripheral\usbd_msc),I found there is a bug about write to flash...
I am working on a new design for the nRF52832. I need to match an antenna to the device. My understanding is that the output impedance of the nRF52832 is 53 + J66 for best...
I am unable to toggle LED's on server boards, using Push buttons on client boards. flashed the light_switch client,server, provisioning images on nrf52832 boards using nrf5SDKforMeshv300src...
I programmed my nRF9160DK with the asset_tracker app using SEGGER Embedded Studio for ARM.
What I did was to open the prj.conf file and changed the following from "n" to...
