But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Should the DEBUG compiler flag be removed before flashing a board that should enter sd_power_system_off? I've seen some troubleshooting guides mention that Debug mode can...
I have set up the thread border router. I connected the NCP (a nrf52840) with a usb cable to a raspberry pi. Now I wonder if it is possible to connect the raspberry pi with...
Hi all,
Currently, I am working on Nrf52 DK with nRF52832 on Keil IDE. My focus is MQTT with 2 nRF52s and RPi. I have succesfully used examples in SDK, but now I am trying...
Hello,
I have got new rigado-301-A-R module, I want to know following things as I want to work on linux and i have a custom board just like rigado 301 eval board.
1. Procedure...
I have an embedded platform running JerryScript. Now, I need to add BLE functionality to it. The BLE module (connectivity chip) will be used is nRF52840. For this, I guess...
I’m trying to program a custom board with nrfjprog, but cannot get it connected correctly. (Connection is standard SEGGER cable, segger mini edu)
nrfjprog -f NRF52 --halt...
hi ，i have a problem! how to slow down the update speed when bootloader receiving the pack. my project is base on the SDK 15.2.0,s112 ,secure_bootloader example ,nRF52810
Dear nordic,
i want to create a low power current consumption ADC. i don't need adc value in every time. my need is just take adc value and disable it.
whenever i want...
HI,
I'm currently working with two chips RF24L01+.
Each chip switch in sending role to receiving role several times. By default, I set them in sending role and I whait...
I use sdk15.2 and nrf52832.
I copy i2s examples to nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ ble_app_hrs ,and nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ ble_app_hrs_freertos...
Hey all,
So I'm new to the Nordic world and I am having some trouble programming the SoftDevices API. After I compile my code, I get the S112 hex file and try to use this...
Hi Nordic,
I am working on a NRF52 DK with the example code ble_app_interactive. I am using the NRF52 DK as a central and trying to connect to a peripheral hearing aid....
Hi guys. Why the Android Mesh app can not receive the the publish data from the 0xffff address?
As we do below:
step 1 : we use 2xP10040 development kit and an android...
