But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Developed with SDK 15.0.0. and s132_nrf52_6.0.0_softdevice
After I generate the DFU package, and upload it with nRF Toolbox, it will returns " Upload failed: REMOTE DFU...
SDK 15.0.0, s132_nrf52_6.0.0_softdevice
I have followed the instruction below:
https://devzone.nordicsemi.com/f/nordic-q-a/29067/installing-micro-ecc-issue/115222#115222...
Hello,
Nrf52832 ibeacon broadcast signal is unstable, and the rssi deviation of left and right upper and lower signals before and after the detection of the same distance...
Hello,
I'm working on some LED sequences using the NRFX PWM driver and I can't get the durations I want right.
Let's say that I want a semi-blinking LED (100% - 50% -...
HI
platform:
sdk:15.0.0
52840
\nRF5_SDK_15.0.0_a53641a\examples\dfu\secure_bootloader\pca10040_uart_debug
I want encode(uart) dfu packet not by nrfutil:
(nrfutil...
In my design, I am using a module based on the NRF52832, with a specified LF clock accuracy of +/-250ppm. In my application, I am using v15.0.0 of the SDK with SoftDevice...
hello, we would like to know which development environment Nordic Semi supports/recommends for NRF52832-QFAA-R (except GCC) Is there a special offer from a manufacturer (e...
I'm in the process of scoping out a new project that is in the realm of robotics. It involves one wireless controller that a person would use to turn and drive four wireless...
Hi there,
I have found a similar thread that dates back from a year ago ( https://devzone.nordicsemi.com/f/nordic-q-a/29073/altering-qspi-address-mode ) but I would like...
I created a application that sometimes uses the BLE for 10 seconds. To turn on the BLE I'm using the function
and to turn off the BLE I'm using the function
I already...
Hello!
I'm trying to interface the DHT11 with my DK. I'm coming from Arduino where all I had to do is to drop some library and instantiate an object. Here with the nRF52...
Hello
I compiled the example ble_app_hrs (ble_app_hrs_pca10056_s140) from SDK 15.0 in IAR 8.11.1
I used softdevice included in the SDK15. (s140_nrf52840_5.0.0-1.alpha_softdevice...
Hi All,
Need a help,
To achieve a long RADIO range i.e Gazell(nordic proprietary RF) range, we are using Nrf52832 with SKY66112.
To control the SKY66112 in PA/LNA...
If we are using an external RTC(for example, PCF85063) with a 32.768kHz XTAL, can we rely on the internal RC oscillator on nRF52840 for the power savings in Deep Sleep mode...
