I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
Dear Engineers!
have a questions about the Input circuit of nRF52.
I have to monitor the signal LEVEL from some sensor. The signal can be Positive or Negative current...
Hi,
I have a board with a NRF52 (3rd party board), there is a 32MHz crystal with the correct load capacitors on, but the crystal is outputting 1MHz on a scope (Tektronix...
Hi,
I'd like to output some audio data through i2s. It's quite easy to understand your examples provided on infocenter, however, I can't get my code to work.
Here is...
Hi all, I'm working on sdk11.0.0 and s130 softdevice. In my project I need to take data from sensor board through uart and send to mobile through ble for every 500ms. Sensor...
Hi guys
I want connect nrf51822 (Raytac MDBT40) by my phone(HTC battery one android 4.4.2).
I use softdevice 130(ver.2.0.0) and SDK 11 demo code under KEIL ARM 5.
...
when i run sudo nrfutil dfu serial -pkg my_package.zip -p/dev/ttyACM0 i get the following error:
pc_ble_driver_py.exceptions.NordicSemiException: Failed to send init packet...
Hi
I am working with mbed targetting for ReadbearLab Ble Nano. I am trying to encrypt payload before sendind it with:
include "nrf_ecb.h"
...
int main(void)
{
...
Hi, i'm using keil and i would like to run the fpu_fft example to perform a fft. The example works if I set 128 or 256 as number of input vector data as you can see in the...
I'm using SDK 6 + S110 v7.
Is it possible to use device manager to perform bonding but don't write bond information persistently in flash?
With old bond manager I could...
Could someone please guide me through the process?
I believe it can be done through nRF Studio which I have downloaded, but don't know how to proceed from there???
Tks...
Dears,
I am developing a ANCS application with nus service on our product. There are a few problems I don't know how to fix it.
My problem is that :
1. ANCS will not disconnect...
Hey guys,
I have designed one custom PCB based on BMD301 in which I am observing some weird behavior on RESET pin. I have connected reset pin of BMD301 i.e. P0.21 to 3...
How do I deny a connection if the connection is unencrypted? I'm currently trying to do it with the peer_manager using
case PM_EVT_CONN_SEC_FAILED:
{
/** In some cases...
