But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
I need 3 time aligned PWM channels (period of all three channels needs to start at the same time) at about 100 Hz with 16 bit resolution on the duty cycle. I also need to...
hello,
I used nrf52 and softdevice 2.0.1 and i have a big problem.
For some times the BT works perfectly but after i connect more then 4 devices for some reason
the...
Hi,
I need to check the emission of my custom nrf52832 board design and I need an spectrum analyzer... To see if my design would pass the regulations and tests.
I was...
Hi Nordic,
It's hard to find an example to talk about the event of advertising. I checked the advertising chart and know I will get the event BLE_GAP_EVT_TIMEOUT. Where can...
Hi,
I attended a training session run by the BT SIG last week and met a helpful Nordic chap who, when I mused about how I was using a programming board to run a sensor...
Hi i am having doubt in RTC configuration.I am using RTC1 and i want to produce ticks for every 1 minute.I have combined the UART and RTC example to get the RTC output in...
Hello
i am using the Nrf52 with pca 10036 board. i am working on fruitymesh to work on visualgdb.
i am getting problem here
"#pragma pack(push)
"#pragma pack(4)
...
Hello, i need to count 1 or 2 minutes. Someone can recommend me if to do that is easier to use app_timer or RTC?
Which is the value that i have to put in the prescaler...
Hi,
I have bootloader ,Application with buttonless dfu (with FreeRTOS) and S132 v3.0,
Flashed SD3.0 and then bootloader with debug support. After updating application zip...
Hi all
I use the nRF52832 and the SoftDevice S132 V2.0.1. When I perform a soft reset (NVIC_SystemReset) while the SoftDevice is running, the fault handler is triggered...
Sorry i'm survey in forum ,and try for a week , the problem still there , please help me !!
I'm try to compile APP1 in IROM1( Start:0x1B000 Size:0x4650) ,APP2 in IROM2...
In Nordic's example GCC projects, the Makefile of the SD examples have -DSOFTDEVICE_PRESENT defined. However I noted that even though it is defined here, in nrf_drv_common...
I have a 1 second app_timer running which increments a 1 second variable used as unix time. We have a 32Khz Xtal, etc, which should result in good accuracy.
I have noticed...
The QFN package has an exposed gnd pad. Are thermal vias required in this gnd pad? The reference design has a 4x4 thermal via array. I believe this is only there because Altium...
Hello,
I'm using a BMD200 module (with a nRF51 chip inside) and the custom_board.h provided by Rigado along with their EVK. I'm also using a BMD200 on a board I developed...
